CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] eg &g torque systems servo card manual

Posted by Dan Mauch
on 2004-09-30 09:52:12 UTC
Not true. My Tree mill uses west amp servo boards and they two run off
+/-15.
I will probably replace the existing servo/servo amps with new ones from
www.cncteknix.com They are similar to the 200V Rutex but are much more
sophisticated at about the same price. I have one running on my work bench
and it is very promising for the larger machines that have 130V PMDC servo
motors.
Dan

----- Original Message -----
From: "Paul" <no.spam27@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, September 30, 2004 10:28 AM
Subject: Re: [CAD_CAM_EDM_DRO] eg &g torque systems servo card manual


>
> Hi Steve
>
> +/15V control - Are you sure ???
> Most analogue amps use +/10V control voltage. If it is a typo, then the
> Copley
> 422 amp will probably work (assuming it is 15A peak).
>
> Regards, Paul.
>
> On Thursday 30 September 2004 13:53, steve wrote:
>> any suggestions
>> for a possible replacement drive? 15amp, tach feed back servo motors,
>> 100vdc bus power, +15/0/-15 control voltage., d/a i think is 5v.? any
>> help is greatly appreciated.
>
> --
> irc channel for EMC users at irc.freenode.org
> /join #emc
>
> Pieces of seven! Pieces of seven! (Hrm, parroty error)
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>

Discussion Thread

steve 2004-09-30 09:02:55 UTC eg &g torque systems servo card manual Paul 2004-09-30 09:32:37 UTC Re: [CAD_CAM_EDM_DRO] eg &g torque systems servo card manual Dan Mauch 2004-09-30 09:52:12 UTC Re: [CAD_CAM_EDM_DRO] eg &g torque systems servo card manual Paul 2004-09-30 10:40:43 UTC Re: [CAD_CAM_EDM_DRO] eg &g torque systems servo card manual