Re: Cap at the Gecko, motor heating, fuse protection??
Posted by
Polaraligned
on 2005-02-08 04:57:28 UTC
So what are your personal thoughts on running a motor over it's
rated voltage? Does is not matter then because the Gecko limits
the current?
Thanks,
Scott
rated voltage? Does is not matter then because the Gecko limits
the current?
Thanks,
Scott
> Well, that's the problem! Power levels well within the continuousratings
> of the motor WILL destroy it if the power is not getting out of themotor.
>torque all
> In other words, say the motor's continuous torque rating allows it to
> produce
> 250 Oz-In. You can feed the motor a current that produces that
> day without harm. You can figure out what POWER level that is, bygreater!
> multiplying
> the current by the voltage drop due to the winding resistance. But,
> when the motor
> is spinning at a high speed, the POWER into the motor will be far
> The continuous current should not be exceeded for more than a secondor so,
> ever. So, that is the real limit - current or torque, NOT POWER!OUTPUT power,
>
> If you try to watch the iput power, you need to also watch the
> to know how much heat is being generated.
>
> But, an RMS sensor based on the current will produce a pretty accurate
> picture
> of the heating that is occurring in the motor. Motor heating is
> proportional to
> current squared, not power into the motor.
>
> Jon
Discussion Thread
notoneleft
2005-02-05 13:26:55 UTC
Export G-Code from AutoCAD macro
Will
2005-02-06 07:35:48 UTC
Re: Export G-Code from AutoCAD macro
notoneleft
2005-02-06 11:47:48 UTC
Re: Export G-Code from AutoCAD macro
R Rogers
2005-02-06 17:12:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Export G-Code from AutoCAD macro
notoneleft
2005-02-06 20:14:20 UTC
Re: Export G-Code from AutoCAD macro
R Rogers
2005-02-06 21:29:16 UTC
Cap at the Gecko, motor heating, fuse protection??
Les Newell
2005-02-07 01:09:50 UTC
Re: [CAD_CAM_EDM_DRO] Cap at the Gecko, motor heating, fuse protection??
Jon Elson
2005-02-07 09:38:35 UTC
Re: [CAD_CAM_EDM_DRO] Cap at the Gecko, motor heating, fuse protection??
Polaraligned
2005-02-07 10:36:26 UTC
Re: Cap at the Gecko, motor heating, fuse protection??
Jon Elson
2005-02-07 22:00:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cap at the Gecko, motor heating, fuse protection??
Polaraligned
2005-02-08 04:57:28 UTC
Re: Cap at the Gecko, motor heating, fuse protection??
turbulatordude
2005-02-08 06:38:11 UTC
Re: Cap at the Gecko, motor heating, fuse protection??
Jon Elson
2005-02-08 10:11:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cap at the Gecko, motor heating, fuse protection??
Jon Elson
2005-02-08 10:15:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cap at the Gecko, motor heating, fuse protection??
Blue
2005-02-09 17:44:25 UTC
Re: [CAD_CAM_EDM_DRO] Export G-Code from AutoCAD macro
wthomas@g...
2005-02-09 19:49:57 UTC
Re: [CAD_CAM_EDM_DRO]W.E.T.Export G-Code from AutoCAD macro
notoneleft
2005-02-09 20:07:58 UTC
Re: Export G-Code from AutoCAD macro