RE: [CAD_CAM_EDM_DRO] Re: Encoder circuits for parallel port hookup?

Thanks for the response Art!

Hmmm.. I ended up getting some pretty cheap mechanical encoders, and
just used some gearing to increase the res... But I seem to be getting a
problem with this. I'm guessing there may be some bouncing of the
signal? I'm using Mach2 (will use Mach3, so I can do both X/Y soon)..
Sometimes it seems like the program will detect 2-hops instead of one,
and sometimes it'll switch out of the MPG mode (I'm guessing this is
debounce and that Mach2 is detecting an invalid Quadrature sequence and
wisely bailing out of the mode?)

Can I use some little capacitors with resistors across them or such to
filter this?

Thanks
Abby

> -----Original Message-----
> From: art [mailto:fenerty@...]
> Sent: 23 February 2005 13:44
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] Re: Encoder circuits for
> parallel port hookup?
>
>
>
> Hi:
> >>>> What I am looking for is the circuit diagrams that show
> how to hook
> > up
> >> an optical encoder to the parallel port (I a
>
> No signal filters are usually necessary, you hook the A and
> B quadrature
> up to the pins on
> the printer port directly, and you have to hook the signal
> gound to pin 25.
> Thats it. Mach3 can read
> up to 7 of these if you have enough pins, but when reading
> from a printer
> port, your limited to the nyquist
> frequency of the program reading it in terms of speed. In
> Mach3's case, at
> 25Khz mode, you are limited to
> about 12500 pulses per second on the encoder, howver, Windows
> being Windows,
> I recommend a 10000
> pulse limit and 20000 in 45Khz mode.
>
> I have seen some DOS software that wil read faster
> though, and it is
> possible for a Windows DRO program to
> do up to 50000 per seconjd from an encoder if it doesn't have
> to do motor
> movements and such to limit
> the interrupt time. I have letters from several that have
> encoders hooked
> up as semi-closed loop correctors
> and they seem to work well within those limits. Personally, I
> haven't had
> time to hook up my linear scales to Windows yet,
> but intend to do so next month to put closed loop corrections
> into the code
> base for Mach3 anyway..
>
> Marris has a post recently on the gecko group about hooking
> an encoder
> directly to a motor to make it follow the encoder
> with very simple circuitry as well...
>
> Thanks,
> Art
> www.artofcnc.ca
> ----- Original Message -----
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@..., timg@...
> Moderator: pentam@... indigo_red@...
> davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com
> to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........ bill
List Mom List Owner


Yahoo! Groups Links