RE: [CAD_CAM_EDM_DRO] Re: milling spindle on a CNC router
Posted by
Dave Halliday
on 2006-02-19 13:51:23 UTC
The router depends on the spindle speed for cooling. Lower the speed
and you remove the cooling.
Shorter life / lower duty cycle.
Routers that have inherent variable speed are OK though -- they were
designed for this.
Dave
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
and you remove the cooling.
Shorter life / lower duty cycle.
Routers that have inherent variable speed are OK though -- they were
designed for this.
Dave
> -----Original Message-----http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of jfglass2001
> Sent: Sunday, February 19, 2006 12:41 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Re: milling spindle on a CNC router
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "dayap1" <dayap@...> wrote:
> >
> > If it uses a Fixed speed router, you can get a router speed
> controller
> > from many sources (Woodcraft, Harborfreight) that will slow down
> the
> > router.
> > Of course, the torque will be quite low, so you will need to tale
> very
> > light cuts.
> >
> > Regards.
> > Daya.
> >
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "jfglass2001"
> <jfglass2001@>
> > wrote:
>
> >From what I understand though, it tends to wear out the router when
> you use a speed controller like that. And you're correct, there is
> very little torque...
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@..., timg@...
> Moderator: pentam@... indigo_red@...
> davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com
> to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
Discussion Thread
jfglass2001
2006-02-15 03:28:07 UTC
milling spindle on a CNC router
dayap1
2006-02-19 11:55:35 UTC
Re: milling spindle on a CNC router
jfglass2001
2006-02-19 12:40:38 UTC
Re: milling spindle on a CNC router
Dave Halliday
2006-02-19 13:51:23 UTC
RE: [CAD_CAM_EDM_DRO] Re: milling spindle on a CNC router