CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Udated DRO

Posted by John Guenther
on 2000-07-04 05:25:38 UTC
I would assume it would since this is a nice way of driving a rotary encoder
for linear motion without attaching it to the lead screw. The board doesn't
care how you drive your encoder, it just counts pulses.

John Guenther
-----Original Message-----
From: wanliker@... [mailto:wanliker@...]
Sent: Tuesday, July 04, 2000 1:56 AM
To: CAD_CAM_EDM_DRO@egroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Udated DRO


In a message dated 7/3/00 10:44:54 AM Mountain Daylight Time,
axtein@... writes:

<<
OOPS,Sorry for not including the URL:
www.surfsouth.com/~axtein/dro/dro1/index.html
>>
Will this same system work with the DRO boards from Camtronics and
Tom? I already have that board.
bill

----------------------------------------------------------------------------
--



----------------------------------------------------------------------------
--
Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.

Addresses:
Post message: CAD_CAM_EDM_DRO@egroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
Moderator: jmelson@... [Moderator]
URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
FAQ: http://www.ktmarketing.com/faq.html
bill,
List Manager



[Non-text portions of this message have been removed]

Discussion Thread

wanliker@a... 2000-06-30 21:04:03 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO A. G. Eckstein 2000-07-03 09:25:29 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO A. G. Eckstein 2000-07-03 09:32:55 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO wanliker@a... 2000-07-03 22:56:04 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO John Guenther 2000-07-04 05:25:38 UTC RE: [CAD_CAM_EDM_DRO] Udated DRO Bob Bachman 2000-07-06 14:05:30 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO A. G. Eckstein 2000-07-06 14:31:08 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO Bob Bachman 2000-07-06 17:56:14 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO A. G. Eckstein 2000-07-07 03:37:44 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO Ian Wright 2000-07-07 11:37:08 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO A. G. Eckstein 2000-07-07 14:07:07 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO Alison & Jim Gregg 2000-07-08 21:27:16 UTC Re: [CAD_CAM_EDM_DRO] Udated DRO