CAD CAM EDM DRO - Yahoo Group Archive

Re: Geckodrive asking for user input

Posted by caudlet
on 2006-07-06 12:12:29 UTC
> >
> > 2) Change the COMMON terminal spec from +5VDC to GND. The G203
> > requires only 2mA max to operate step/direction optos instead of
> > 16mA. The G203 has a max step pulse frequency of 350kHz (>10,000
> RPM
> > on a 1.8-degree motor) without any funny G201 step/direction
> timing
> > restrictions.
> >
Regardless of the change, it will result in short term support issues.
For all of the units I sell I have always made the option to have +5
or ground as common on my cards. We normally ship them as +5 common
units. On complete units like the MP1000 series changing that means
opening the case. I will brace myself for the calls where "I just
hooked up my Gecko's and nothing is moving" (:[

What does lowering the input current requirements do to the noise
immunity? I predict there will be increased noise issues on drives
used in plasma applications or with VFD's. Common Ground may add to
that as well.

PS...I would love to see a line of higher voltage/ higher current
drives (especially in the Servo line).

Tom Caudle
North Texas

Http://www.CandCNC.com
"We just made CNC easier!"

Hardware for Home Shop CNC:
Low cost, powered/isolated, breakout card
AC and DC "Drive Saver" power controls
2nd Generation Digital THC
Handheld Manual Pulse Generators (MPG)

Discussion Thread

Mariss Freimanis 2006-07-05 20:32:21 UTC Geckodrive asking for user input Bob Muse 2006-07-05 20:45:31 UTC Re: [CAD_CAM_EDM_DRO] Geckodrive asking for user input Mariss Freimanis 2006-07-05 21:21:55 UTC Re: Geckodrive asking for user input Tony Jeffree 2006-07-06 00:32:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Geckodrive asking for user input Dan Mauch 2006-07-06 06:54:28 UTC Re: [CAD_CAM_EDM_DRO] Geckodrive asking for user input Alan Marconett 2006-07-06 07:48:06 UTC RE: [CAD_CAM_EDM_DRO] Geckodrive asking for user input Mariss Freimanis 2006-07-06 08:30:40 UTC Re: Geckodrive asking for user input Mariss Freimanis 2006-07-06 08:38:26 UTC Re: Geckodrive asking for user input Alan Marconett 2006-07-06 09:05:25 UTC RE: [CAD_CAM_EDM_DRO] Re: Geckodrive asking for user input Mariss Freimanis 2006-07-06 09:30:09 UTC Re: Geckodrive asking for user input erich10983@a... 2006-07-06 09:51:56 UTC Re: Geckodrive asking for user input Mariss Freimanis 2006-07-06 10:18:09 UTC Re: Geckodrive asking for user input Tony Jeffree 2006-07-06 11:10:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Geckodrive asking for user input caudlet 2006-07-06 12:12:29 UTC Re: Geckodrive asking for user input Mike Noltkamper 2006-07-06 20:14:09 UTC Re: [CAD_CAM_EDM_DRO] Geckodrive asking for user input turbulatordude 2006-07-07 08:48:19 UTC Re: Geckodrive asking for user input JCullins 2006-07-07 11:03:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Geckodrive asking for user input