Re: degrees of freedom Was: Angle Iron Ways
Posted by
Graham Stabler
on 2006-08-23 04:05:03 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Raymond Heckert" <jnr@...> wrote:
easy to make where as a linear axis is not so bad. The rotobot is a
tad tricky too though you can get ring guides and gears from
hepco/wisecarver and the like.
Graham
>me....
> Yeah, I can see that that would work, but it seems more complex to
> but, that might just be the booze talkin'...Personally I don't think stiff adjustable length struts are all that
>
> RayHex
easy to make where as a linear axis is not so bad. The rotobot is a
tad tricky too though you can get ring guides and gears from
hepco/wisecarver and the like.
Graham
Discussion Thread
Dennis Schmitz
2006-08-18 21:52:10 UTC
degrees of freedom Was: Angle Iron Ways
Dennis Schmitz
2006-08-18 22:02:54 UTC
Re: degrees of freedom Was: Angle Iron Ways
Graham Stabler
2006-08-19 13:54:26 UTC
Re: degrees of freedom Was: Angle Iron Ways
Graham Stabler
2006-08-19 14:06:13 UTC
Re: degrees of freedom Was: Angle Iron Ways
leslie watts
2006-08-20 03:15:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: degrees of freedom Was: Angle Iron Ways
Dennis Schmitz
2006-08-20 13:24:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: degrees of freedom Was: Angle Iron Ways
Raymond Heckert
2006-08-20 18:31:38 UTC
Re: [CAD_CAM_EDM_DRO] degrees of freedom Was: Angle Iron Ways
Stephen Wille Padnos
2006-08-20 19:12:57 UTC
Re: [CAD_CAM_EDM_DRO] degrees of freedom Was: Angle Iron Ways
Dennis Schmitz
2006-08-20 20:30:53 UTC
Re: [CAD_CAM_EDM_DRO] degrees of freedom Was: Angle Iron Ways
Graham Stabler
2006-08-21 02:41:41 UTC
Re: degrees of freedom Was: Angle Iron Ways
Graham Stabler
2006-08-21 02:42:08 UTC
Re: degrees of freedom Was: Angle Iron Ways
Alan Marconett
2006-08-21 08:02:25 UTC
RE: [CAD_CAM_EDM_DRO] degrees of freedom Was: Angle Iron Ways
Stephen Wille Padnos
2006-08-21 08:15:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: degrees of freedom Was: Angle Iron Ways
turbulatordude
2006-08-21 09:09:36 UTC
Re: degrees of freedom - Hexapod
Graham Stabler
2006-08-21 11:37:52 UTC
Re: degrees of freedom - Hexapod
Dennis Schmitz
2006-08-21 18:38:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: degrees of freedom Was: Angle Iron Ways
Raymond Heckert
2006-08-22 22:20:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: degrees of freedom Was: Angle Iron Ways
Graham Stabler
2006-08-23 04:05:03 UTC
Re: degrees of freedom Was: Angle Iron Ways
Raymond Heckert
2006-08-23 07:24:49 UTC
Re: [CAD_CAM_EDM_DRO] degrees of freedom Was: Angle Iron Ways
Graham Stabler
2006-08-23 11:43:57 UTC
Re: degrees of freedom Was: Angle Iron Ways