Re: [CAD_CAM_EDM_DRO] Video of the G203 Vampire running a cnc retrofitted Mill drill
Posted by
Dan Mauch
on 2006-11-15 13:17:12 UTC
I used the 452 oz in MCG IH34110 stepper motors that I sell. I also tested
the 762 oz in IH34112 stepper motors and they were fine also but I think
overpowered. I switched back to the 452 oz in motors.
I used a 3/1 ratio timing belt drive only because I use and test this
machine with various motors. The motor mount is set up to take C34 or Nema34
motors and with an adapter plate could run nema23 motors.
I used 5/8"D .2 pitch 5 TPI ballscrews from McMaster Carr but would
recommend the Nook over them.
I used two ballnuts on the X axis on each side of the ball nut drive block
so I have zero backlash. The Y axis also has two ballnuts. The Z axis uses
my "solving the mill drill backlash problem" eccentric bushings on the
pinion cross shaft for .002 backlash.
Other than that it is stock except for the link belts on the power head
drive pulleys
Dan Mauch
low cost stepper and servo motors.
cases for Gecko drives
kits and assembled 3-4 axis drives
www.camtronics-cnc.com
www.seanet.com/~dmauch
the 762 oz in IH34112 stepper motors and they were fine also but I think
overpowered. I switched back to the 452 oz in motors.
I used a 3/1 ratio timing belt drive only because I use and test this
machine with various motors. The motor mount is set up to take C34 or Nema34
motors and with an adapter plate could run nema23 motors.
I used 5/8"D .2 pitch 5 TPI ballscrews from McMaster Carr but would
recommend the Nook over them.
I used two ballnuts on the X axis on each side of the ball nut drive block
so I have zero backlash. The Y axis also has two ballnuts. The Z axis uses
my "solving the mill drill backlash problem" eccentric bushings on the
pinion cross shaft for .002 backlash.
Other than that it is stock except for the link belts on the power head
drive pulleys
Dan Mauch
low cost stepper and servo motors.
cases for Gecko drives
kits and assembled 3-4 axis drives
www.camtronics-cnc.com
www.seanet.com/~dmauch
----- Original Message -----
From: "KM6VV" <KM6VV@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, November 15, 2006 12:16 PM
Subject: RE: [CAD_CAM_EDM_DRO] Video of the G203 Vampire running a cnc
retrofitted Mill drill
> Hi Dan,
>
> That looks great! The mill looks a lot like my RF-31 which is in need of
> a
> conversion.
>
> If you don't mind, what size steppers, pulley ratio and ballscrew pitch
> are
> you using?
>
> Hay; that will make a nice KIT!
>
> Alan KM6VV
>
>> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Dan Mauch
>
>
>>
>> I mentioned that I would post a video of the G203's running my mill
>> drill.
>> Here it is
>> http://video.google.com/videoplay?docid=6951643805663907424
>> Dan Mauch
>> low cost stepper and servo motors.
>> cases for Gecko drives
>> kits and assembled 3-4 axis drives
>> www.camtronics-cnc.com
>> www.seanet.com/~dmauch
>>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
Discussion Thread
Dan Mauch
2006-11-15 11:03:41 UTC
Video of the G203 Vampire running a cnc retrofitted Mill drill
KM6VV
2006-11-15 12:25:36 UTC
RE: [CAD_CAM_EDM_DRO] Video of the G203 Vampire running a cnc retrofitted Mill drill
Dan Mauch
2006-11-15 13:17:12 UTC
Re: [CAD_CAM_EDM_DRO] Video of the G203 Vampire running a cnc retrofitted Mill drill
BRIAN FOLEY
2006-11-15 13:48:48 UTC
Re: [CAD_CAM_EDM_DRO] Video of the G203 Vampire running a cnc retrofitted Mill drill
John Dammeyer
2006-11-15 14:38:39 UTC
RE: [CAD_CAM_EDM_DRO] Video of the G203 Vampire running a cnc retrofitted Mill drill