Re: [CAD_CAM_EDM_DRO] Re: linear bearings for sale or swap

Bob Campbell wrote:

> mariano,
>
> What size are they 15mm, 20mm or 25mm?
>
> Bob Campbell
>

Bob; I think that the small ones are 20mm and the big one is bigger, tomorrow I will measure them , it is 2.00 a.m , now

>
> ----- Original Message -----
> From: diazden <diazden@...>
> To: <CAD_CAM_EDM_DRO@egroups.com>
> Sent: Friday, June 16, 2000 8:33 AM
> Subject: Re: [CAD_CAM_EDM_DRO] Re: linear bearings for sale or swap
>
> >
> > hello guys; I have three sets of linear bearings ( x, y, z, axis) each
> set including two linear rails and four mounting bearings ,
> > they are second hand and are from a gantry robot no visible damage on the
> tracks,and. they are as follows:
> > one set THK model TK1 43 inches long
> > one set THK model TK1 51 inches long
> > one set THK model TK2 62 inches long
> > price US 100 each set or will swap for one servo drive per axis (the
> $99 one from Mariss will do
> > regards
> > mariano
> >
> >
> >
> >
> > ------------------------------------------------------------------------
> > To email plain text is conventional, to add graphics is divine.
> > We'll show you how at www.supersig.com.
> > http://click.egroups.com/1/6811/4/_/423600/_/963846219/
> > ------------------------------------------------------------------------
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
> discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@egroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> > Moderator: jmelson@... [Moderator]
> > URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > FAQ: http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager
>
> ------------------------------------------------------------------------
> Wish you had something rad to add to your email?
> We do at www.supersig.com.
> http://click.egroups.com/1/6810/4/_/423600/_/963848157/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager