Re: [CAD_CAM_EDM_DRO] Re: linear bearings for sale or swap

Bob;
the ones marked TK2 measures 28x28mm and it sliding base measures 90x78mm the assembled height is 50mm
the ones marked TK1 is 23x23mm ,slider block base is 47.73mm wide and the assembly height is 37.21 MM .

Bob Campbell wrote:

> mariano,
>
> What size are they 15mm, 20mm or 25mm?
>
> Bob Campbell
>
> ----- Original Message -----
> From: diazden <diazden@...>
> To: <CAD_CAM_EDM_DRO@egroups.com>
> Sent: Friday, June 16, 2000 8:33 AM
> Subject: Re: [CAD_CAM_EDM_DRO] Re: linear bearings for sale or swap
>
> >
> > hello guys; I have three sets of linear bearings ( x, y, z, axis) each
> set including two linear rails and four mounting bearings ,
> > they are second hand and are from a gantry robot no visible damage on the
> tracks,and. they are as follows:
> > one set THK model TK1 43 inches long
> > one set THK model TK1 51 inches long
> > one set THK model TK2 62 inches long
> > price US 100 each set or will swap for one servo drive per axis (the
> $99 one from Mariss will do
> > regards
> > mariano
> >
> >
> >
> >
> > ------------------------------------------------------------------------
> > To email plain text is conventional, to add graphics is divine.
> > We'll show you how at www.supersig.com.
> > http://click.egroups.com/1/6811/4/_/423600/_/963846219/
> > ------------------------------------------------------------------------
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
> discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@egroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> > Moderator: jmelson@... [Moderator]
> > URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > FAQ: http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager
>
> ------------------------------------------------------------------------
> Wish you had something rad to add to your email?
> We do at www.supersig.com.
> http://click.egroups.com/1/6810/4/_/423600/_/963848157/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager