Re: Pixie error connection
Posted by
toolspindoctor
on 2007-07-15 17:16:17 UTC
I gave it a try and connected +5v to the + of the relay and Pixie
error to the - of the relay and it does not trip the relay so I assume
it is still going to 0 volts. Guess I'll need to go the transistor
route...
Thanks
Keith
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Graham Stabler" <grezmos@...>
wrote:
error to the - of the relay and it does not trip the relay so I assume
it is still going to 0 volts. Guess I'll need to go the transistor
route...
Thanks
Keith
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Graham Stabler" <grezmos@...>
wrote:
>polarity?
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "toolspindoctor"
> <clarkfamily5@> wrote:
> >
> > Graham,
> >
> > I am trying to drive a Dayton Solid State Relay, Input DC, Maximum
> > Input Voltage 32 VDC, Minimum Input Voltage 3.5 VDC, Output DC,
> > Minimum Output Voltage 0 VDC Grainger part #5Z950. Probably too much
> > draw and it drops the Pixie to 0volts each time I connect. Must be a
> > way to place a resistor...
> >
> > Thanks,
> > Keith
>
> In mentions opto coupling so am I right that the "coil" has a
>energized.
> If so connect the + to 5v and the negative to the pixie. That way
> when the pixie pulls the output low the led in the opto will be
>
> Connecting the relay the other way will tend to pull the pixie down to
> ground and cause the fault.
>
> Please apply a pinch of salt as I have not used SS relays but I think
> I am right.
>
> Graham
>
Discussion Thread
toolspindoctor
2007-07-14 15:38:26 UTC
Pixie error connection
Mark Vaughan
2007-07-15 01:58:50 UTC
RE: [CAD_CAM_EDM_DRO] Pixie error connection
toolspindoctor
2007-07-15 08:44:01 UTC
Re: Pixie error connection
Mark Vaughan
2007-07-15 09:45:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Graham Stabler
2007-07-15 10:51:57 UTC
Re: Pixie error connection
Tom Hubin
2007-07-15 11:07:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Mark Vaughan
2007-07-15 11:22:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: Pixie error connection
BRIAN FOLEY
2007-07-15 12:02:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
toolspindoctor
2007-07-15 12:59:50 UTC
Re: Pixie error connection
toolspindoctor
2007-07-15 13:01:58 UTC
Re: Pixie error connection
toolspindoctor
2007-07-15 13:04:28 UTC
Re: Pixie error connection
Mark Vaughan
2007-07-15 14:26:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Mark Vaughan
2007-07-15 14:35:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Pixie error connection
David G. LeVine
2007-07-15 14:50:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Tom Hubin
2007-07-15 15:10:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Graham Stabler
2007-07-15 15:16:34 UTC
Re: Pixie error connection
toolspindoctor
2007-07-15 17:16:17 UTC
Re: Pixie error connection
toolspindoctor
2007-07-15 18:51:53 UTC
Re: Pixie error connection
Tom Hubin
2007-07-15 21:01:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
toolspindoctor
2007-07-15 21:48:32 UTC
Re: Pixie error connection
Tom Hubin
2007-07-15 23:28:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Mark Vaughan
2007-07-16 00:08:49 UTC
RE: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Tom Hubin
2007-07-16 00:39:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Graham Stabler
2007-07-16 02:38:51 UTC
Re: Pixie error connection
Graham Stabler
2007-07-16 02:44:11 UTC
Re: Pixie error connection
Mark Vaughan
2007-07-16 04:26:50 UTC
RE: [CAD_CAM_EDM_DRO] Re: Pixie error connection
toolspindoctor
2007-07-16 04:58:36 UTC
Re: Pixie error connection
toolspindoctor
2007-07-16 05:11:20 UTC
Re: Pixie error connection
James Cullins
2007-07-16 05:27:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
David G. LeVine
2007-07-16 06:34:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
David G. LeVine
2007-07-16 06:39:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
toolspindoctor
2007-07-16 09:32:20 UTC
Re: Pixie error connection
Tom Hubin
2007-07-16 09:51:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Tom Hubin
2007-07-16 11:27:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Pixie error connection
Graham Stabler
2007-07-16 11:40:29 UTC
Re: Pixie error connection
toolspindoctor
2007-07-16 12:20:56 UTC
Re: Pixie error connection
toolspindoctor
2007-08-07 05:18:29 UTC
Re: Pixie error connection