Re: need help to restart an old cnc lathe
Posted by
masroor6350
on 2007-08-04 08:21:15 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Zoran A. Scepanovic"
<zastos@...> wrote:
You are correct, configuration data you mean the parameters for the
lathe? this is only one encouraging responce so far. Is there advice
how to configurate?
Masroor
<zastos@...> wrote:
>this disclaimer follows.
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Hello masroor6350,
>
> Thursday, August 2, 2007, 9:35:04 AM, you wrote:
>
>
> > Thanks to for helping me out! Now I can be more specific. This cnc
> > lathe of KITAMURA, model KNC-50 with FANUC control 2T modal A, PLC
> > KOYO-KOSTAC SR-20 an old model a company using this lathe donated to
> > a local techincal school. The lathe was lying unattended for more than
> > 3 years. Upon restarting the battery was low. The battery was changed,
> > may be some student has done some thing with the RAM of PLC. There are
> > two programable ICs on the RAM, one D2764D has still some program the
> > other IC HM6116LP-2 is completly washed. The RAM serial Nr:
> > 841108426. Need parameters for this IC, The KITAMURA USA are unable to
> > help. If any of the member has a lathe can provide parameters I will
> > be highly obliged, just helping the school gratis.
> > Masroor
>
>
>
> For your information the D2764D is EPROM containing PLC's program
> and HM6116LP is RAM which should hold the configuration data (I
> guess). The RAM chip is always completely washed as soon as it stays
> without any power supply or taken out from it's socket. Try to
> figure out how to initialize your PLC.
>
> - --
> Best regards,
> Zoran A. Scepanovic
> zastos@...
> www.zastos.com
> +381 63 609-993 (GSM)
> +381 61 141-3074 (GSM)
> +381 11 344-0748
>
> *********
> Never underestimate the incompetence of others;
> they always possess the power to amaze.
> Their power is greater than yours.
> *********
>
> Please be advised what was said may be absolutely wrong, and hereby
> I reserve the right to be wrong and admit it in front of the entireworld.
>Thanks Zoran A. Scepanovic,
> -----BEGIN PGP SIGNATURE-----
> Version: PGP SDK 3.2.2
> Comment: ""
>
> iQA/AwUBRrN6VOuYWcfRZxvREQI9lACgxhI6FEBB1GZ2voAlw1gtF8eEbgEAnjCs
> GHzLjfuNH8sGJiY3J95z3nQO
> =0DnD
> -----END PGP SIGNATURE-----
>
You are correct, configuration data you mean the parameters for the
lathe? this is only one encouraging responce so far. Is there advice
how to configurate?
Masroor
Discussion Thread
Thea xxxxx
2007-07-29 10:56:19 UTC
AW: [CAD_CAM_EDM_DRO] need help to restart an old cnc lathe
masroor6350
2007-08-02 00:35:13 UTC
Re: need help to restart an old cnc lathe
Jon Elson
2007-08-02 08:19:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: need help to restart an old cnc lathe
Zoran A. Scepanovic
2007-08-03 11:57:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: need help to restart an old cnc lathe
masroor6350
2007-08-04 08:21:15 UTC
Re: need help to restart an old cnc lathe
Zoran A. Scepanovic
2007-08-04 09:33:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: need help to restart an old cnc lathe