Re: [CAD_CAM_EDM_DRO] Excelon Drill file to MACH3 G-Code.
Posted by
Zoran A. Scepanovic
on 2008-12-14 02:07:15 UTC
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Zdravo John,
Friday, December 12, 2008, 11:54:37 PM, ti rece:
any zeroes suppressed and check your inbox for converter software,
if needed be, you can tweak G-code a little to suit your needs.
- --
Srdacan pozdrav,
Zoran A. Scepanovic
zastos@...
www.zastos.com
+381 63 609-993 (GSM)
+381 11 344-0748
*********
Be who you are and say what you feel because those who mind don't matter and those who matter don't mind.
*********
Please be advised what was said may be absolutely wrong, and hereby this disclaimer follows.
I reserve the right to be wrong and admit it in front of the entire world.
-----BEGIN PGP SIGNATURE-----
Version: PGP SDK 3.2.2
Comment: ""
iQA/AwUBSUTazeuYWcfRZxvREQJcGgCdFhAJnKvic2v8SVhehFc07lZXQVQAoL5C
8TXo7IltMElZ4FPG3h5CJr6o
=9soH
-----END PGP SIGNATURE-----
Hash: SHA1
Zdravo John,
Friday, December 12, 2008, 11:54:37 PM, ti rece:
> Hi,when generating the drill file, set your output to be 2:3 WITHOUT
> I have an excelon drill file created by my Protel PCB software. Would
> someone be able to run this file through a converter to turn it into a
> G-Code file compatible with MACH3? I don't have time to wait for a
> circuit board to be made and I just want to clamp a blank PCB onto the
> table of a mill and have it drill the holes to make sure the prototype
> board will fit properly.
> Thanks
> John
> Automation Artisans Inc.
> http://www.autoartisans.com/ELS/
> Ph. 1 250 544 4950
any zeroes suppressed and check your inbox for converter software,
if needed be, you can tweak G-code a little to suit your needs.
- --
Srdacan pozdrav,
Zoran A. Scepanovic
zastos@...
www.zastos.com
+381 63 609-993 (GSM)
+381 11 344-0748
*********
Be who you are and say what you feel because those who mind don't matter and those who matter don't mind.
*********
Please be advised what was said may be absolutely wrong, and hereby this disclaimer follows.
I reserve the right to be wrong and admit it in front of the entire world.
-----BEGIN PGP SIGNATURE-----
Version: PGP SDK 3.2.2
Comment: ""
iQA/AwUBSUTazeuYWcfRZxvREQJcGgCdFhAJnKvic2v8SVhehFc07lZXQVQAoL5C
8TXo7IltMElZ4FPG3h5CJr6o
=9soH
-----END PGP SIGNATURE-----
Discussion Thread
eugenelambe1
2008-12-12 08:05:16 UTC
boxford 160 slant bed
John Dammeyer
2008-12-12 14:55:59 UTC
Excelon Drill file to MACH3 G-Code.
Jon Elson
2008-12-12 20:21:24 UTC
Re: [CAD_CAM_EDM_DRO] Excelon Drill file to MACH3 G-Code.
Alan Rothenbush
2008-12-12 21:58:00 UTC
RE: [CAD_CAM_EDM_DRO] Excelon Drill file to MACH3 G-Code.
Peter Homann
2008-12-12 23:12:16 UTC
Re: [CAD_CAM_EDM_DRO] Excelon Drill file to MACH3 G-Code.
John Dammeyer
2008-12-13 16:34:44 UTC
RE: [CAD_CAM_EDM_DRO] Excelon Drill file to MACH3 G-Code.
John Dammeyer
2008-12-13 16:34:54 UTC
RE: [CAD_CAM_EDM_DRO] Excelon Drill file to MACH3 G-Code.
John Dammeyer
2008-12-13 16:35:06 UTC
RE: [CAD_CAM_EDM_DRO] Excelon Drill file to MACH3 G-Code.
Jon Elson
2008-12-13 17:31:13 UTC
Re: [CAD_CAM_EDM_DRO] Excelon Drill file to MACH3 G-Code.
Zoran A. Scepanovic
2008-12-14 02:07:15 UTC
Re: [CAD_CAM_EDM_DRO] Excelon Drill file to MACH3 G-Code.