RE: [CAD_CAM_EDM_DRO] help with cad closing points or lines
Posted by
rwwink
on 2009-04-01 05:25:44 UTC
One point that's AutoCAD related.If you draw the two lines that represent
the straight sides of the slot, AutoCAD will "fillet" the lines with
whatever radius is required.
Example: Draw a line, offset it .5625 and start the fillet command. Pick
the two lines near one end and AutoCAD will connect the lines with a radius
the will "mate" with the end of the lines. Do the same for the other end
and yo will have a slot with arcs that fit. The lines do not need to be
parallel either.
R. Wink
_____
From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of William Thomas
Sent: Wednesday, April 01, 2009 4:34 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] help with cad closing points or lines
Hi Gary and All:
Double check the radius for the ends down to four places.
What often happens is
that you have the radius as .281" and the slot width as .5625". The arc
will not meet the side
of the slot as it as it is off by .0005". This a common problem with arc's.
GOD'S BLESSINGS
Bill
On Tue, 31 Mar 2009 19:12:01 -0000, gorf242003 wrote
side will only give me an outside path.
am missing, i tried close polyline but i get the same results.
Open WebMail Project (http://openwebmail. <http://openwebmail.org> org)
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
the straight sides of the slot, AutoCAD will "fillet" the lines with
whatever radius is required.
Example: Draw a line, offset it .5625 and start the fillet command. Pick
the two lines near one end and AutoCAD will connect the lines with a radius
the will "mate" with the end of the lines. Do the same for the other end
and yo will have a slot with arcs that fit. The lines do not need to be
parallel either.
R. Wink
_____
From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of William Thomas
Sent: Wednesday, April 01, 2009 4:34 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] help with cad closing points or lines
Hi Gary and All:
Double check the radius for the ends down to four places.
What often happens is
that you have the radius as .281" and the slot width as .5625". The arc
will not meet the side
of the slot as it as it is off by .0005". This a common problem with arc's.
GOD'S BLESSINGS
Bill
On Tue, 31 Mar 2009 19:12:01 -0000, gorf242003 wrote
> I have 2 slots 9/16 wide they have a slight radius,do an inside profile, one side of the arc will show an inside path the other
> When i put in a cam program to setit up for the cuts, and i try to have it
side will only give me an outside path.
>not have a closed line, i can't seem to get it to close, is there a trick i
> I tried turbocad12 and autocad2009 i assume i am getting this problem from
am missing, i tried close polyline but i get the same results.
>--
> Thanks gary
>
>
Open WebMail Project (http://openwebmail. <http://openwebmail.org> org)
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
Discussion Thread
gorf242003
2009-03-31 12:13:12 UTC
help with cad closing points or lines
William Thomas
2009-04-01 02:34:23 UTC
Re: [CAD_CAM_EDM_DRO] help with cad closing points or lines
rwwink
2009-04-01 05:25:44 UTC
RE: [CAD_CAM_EDM_DRO] help with cad closing points or lines