Re: How do set home position, running turbo cad/cam
Posted by
cassadaga717
on 2010-01-03 07:30:18 UTC
Thanks Ed, I like the input about the limit switches
--- In CAD_CAM_EDM_DRO@yahoogroups.com, ED MAISEY <holmes_ca_2000@...> wrote:
>
> Cassadaga717,
> Â Â Â Â Â Â I'm just a novice at CNC, my first thought about your question and save you money by not having to pay the fire department, is don't worry about limit switches for the time being, you can place them later, I have my machine working for two years now and still have no limit switches, when I produce a program in gcode, I do several dry runs on the computer only and once I am satisfied all is well then I start the machine and might do the first two or three steps in single block until I think its ok, (I am running Mach3),
> Â
> This is how I survive with my machine, I'm sure you will get better advice, from other members, if not you could join the mach2mach3 forum on yahoo, they are very active,
> Â
> Good luck, and make some chips quickly before its to late,
>
>
> ........Edmund.........
>
> --- On Sat, 1/2/10, cassadaga717 <cassadaga717@...> wrote:
>
>
> From: cassadaga717 <cassadaga717@...>
> Subject: [CAD_CAM_EDM_DRO] How do set home position, running turbo cad/cam
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Date: Saturday, January 2, 2010, 6:42 AM
>
>
> Â
>
>
>
> I'm in the final stages of my scratch built CNC and starting to look into the software to run my machine. I have a full copy of Turbo CAD/CAM 11 and after going through the CAM setup I noticed there it no way to detect the limit switches or to jog the machine to a home position. I used the Hobbycnc driver board and their 305oz stepper motors. Although there are inputs for limit switches, it said the inputs are for the software only. I've read all the threads on numerous groups and no one seams to mention about manual moving the machine. Please help, I'm so close and if I don;t get the CNC running, the wife said she was going to burn the wooden monster in the garage.
>
>
>
>
>
>
>
>
> [Non-text portions of this message have been removed]
>
Discussion Thread
cassadaga717
2010-01-02 07:51:30 UTC
How do set home position, running turbo cad/cam
cncnovice
2010-01-02 08:19:39 UTC
Re: How do set home position, running turbo cad/cam
caudlet
2010-01-02 08:54:51 UTC
Re: How do set home position, running turbo cad/cam
ED MAISEY
2010-01-02 08:55:55 UTC
Re: [CAD_CAM_EDM_DRO] How do set home position, running turbo cad/cam
cassadaga717
2010-01-03 07:30:18 UTC
Re: How do set home position, running turbo cad/cam
cassadaga717
2010-01-03 07:32:21 UTC
Re: How do set home position, running turbo cad/cam
cassadaga717
2010-01-03 07:34:09 UTC
Re: How do set home position, running turbo cad/cam
ooo
2010-01-03 11:28:16 UTC
RE: [CAD_CAM_EDM_DRO] Re: How do set home position, running turbo cad/cam
Dan Mauch
2010-01-03 12:25:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: How do set home position, running turbo cad/cam
Dan Mauch
2010-01-03 13:01:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: How do set home position, running turbo cad/cam
Torsten
2010-01-04 02:54:54 UTC
Re: How do set home position, running turbo cad/cam
cassadaga717
2010-01-05 12:29:15 UTC
Re: How do set home position, running turbo cad/cam