Re: [CAD_CAM_EDM_DRO] Rotary Axis home and/or limit switches
Posted by
Roland Jollivet
on 2010-02-05 08:31:53 UTC
But why do you need a limit switch on a rotary axis if it's meant to go
round and round? because it's going to see the 'limit' switch over and over.
The 'homing' switch should be ignored except on homing.
Roland
round and round? because it's going to see the 'limit' switch over and over.
The 'homing' switch should be ignored except on homing.
Roland
On 5 February 2010 16:27, ya_nvr_no <yanvrno@...> wrote:
>
>
> I have added a couple of rotary axis's But am having an issue with coming
> up with a good way to home them. One switch gives me a home position but if
> I rotate one revolution the switch is made again. I am using CNCpro, it uses
> a limit switch as the home switch.(would another program handle this
> better?)
>
> So for example, an issue on the B & C axis.
> Do I home at somewhere >90 degrees then move the B axis to the vertical
> position once I know what that angle is? Manual Zero this location.
> Home the C axis and then rotate it ~180 to find the center of the truncated
> 360 degree rotation? Manual Zero this location
> And on an A table axis I would be limited to less than 360 degrees.
>
> My options are:
> Using a M code or manual toggle switch to disable the homing/limit switches
> after homing
> or
> Using both home and limit switches, create a logic IC circuit/or PLC that
> determines conditions.
>
> I've searched but find no info on how this is handled.
> There has to be a straight forward way to handle this.
> Thanks for any HELP/Direction
>
>
>
[Non-text portions of this message have been removed]
Discussion Thread
ya_nvr_no
2010-02-05 07:41:44 UTC
Rotary Axis home and/or limit switches
Michael Fagan
2010-02-05 07:50:27 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Axis home and/or limit switches
Stephen Wille Padnos
2010-02-05 08:09:03 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Axis home and/or limit switches
Roland Jollivet
2010-02-05 08:31:53 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Axis home and/or limit switches
David LeVine
2010-02-05 12:23:01 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Axis home and/or limit switches
Stephen Wille Padnos
2010-02-05 12:46:39 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Axis home and/or limit switches
Nathan Clark
2010-02-05 21:24:30 UTC
Re: [CAD_CAM_EDM_DRO] Rotary Axis home and/or limit switches
Torsten
2010-02-07 15:38:34 UTC
Re: Rotary Axis home and/or limit switches
Roland Jollivet
2010-02-08 11:49:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Rotary Axis home and/or limit switches
Michael Fagan
2010-02-08 18:21:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Rotary Axis home and/or limit switches
Andrew Mathison
2010-02-10 22:49:25 UTC
Re: Rotary Axis home and/or limit switches
Mark Bingham
2010-02-11 02:45:46 UTC
Re: Rotary Axis home and/or limit switches