Re: CNCing a small lathe
Posted by
polaraligned
on 2010-07-06 19:23:23 UTC
I purchased one of these lathes:
http://www.ajaxcnc.com/cnc_lathe_2.htm
a year ago. They got a shipment that was not covered
properly and the ways got a bit rusted. Cleaned up
nice. Even got brand new ballscrews and ballscrew bearings with it.
They had a bunch of these "defective" lathes. I don't know if
anymore are available. I paid $1k for it. No control but ready to mount servos....
http://www.ajaxcnc.com/cnc_lathe_2.htm
a year ago. They got a shipment that was not covered
properly and the ways got a bit rusted. Cleaned up
nice. Even got brand new ballscrews and ballscrew bearings with it.
They had a bunch of these "defective" lathes. I don't know if
anymore are available. I paid $1k for it. No control but ready to mount servos....
Discussion Thread
bfairey@r...
2010-07-04 08:15:24 UTC
CNCing a small lathe
turbulatordude
2010-07-04 09:22:29 UTC
Re: CNCing a small lathe
Ron Ginger
2010-07-05 04:51:12 UTC
Re: CNCing a small lathe
Jack McKie
2010-07-05 07:00:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Mike Hagen
2010-07-05 11:00:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Jeffrey T. Birt
2010-07-05 13:06:59 UTC
RE: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Danny Miller
2010-07-05 13:10:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
William Thomas
2010-07-05 14:00:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Jeffrey T. Birt
2010-07-05 14:23:17 UTC
RE: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Jon Elson
2010-07-05 14:25:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
William Thomas
2010-07-05 14:35:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Danny Miller
2010-07-05 15:18:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
david@f...
2010-07-05 15:59:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Jon Elson
2010-07-05 18:06:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Jon Elson
2010-07-05 18:18:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Stephen Wille Padnos
2010-07-05 19:50:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
turbulatordude
2010-07-06 04:02:07 UTC
Re: CNCing a small lathe
David Speck
2010-07-06 04:15:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe
Ron Ginger
2010-07-06 05:12:30 UTC
Re: CNCing a small lathe
polaraligned
2010-07-06 19:23:23 UTC
Re: CNCing a small lathe
Mike Hagen
2010-07-06 20:23:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCing a small lathe