CAD CAM EDM DRO - Yahoo Group Archive

Re: E-stop relay welds contacts for load dump resistor

Posted by kzf817
on 2011-01-31 18:43:11 UTC
I think that what Mariss had in mind with the circuit was a way to brake the servo motor to a stop when you have a runaway, such as when an encoder fails, or when you program some really long G00 rapid that is going to crash the cutter into something. I am really liking what you, and a couple of others have said about letting the bleed resistor be a very slow bleed (1k or something similar). So just do a slow discharge of the filter cap, to prevent it from staying charged forever when the machine is down, eliminating stored energy after a minute or so. I can always do an E-stop during a test rapid move, just to see how long it takes for things to stop. If it takes way too long, then I can re-examine things. It sounds like the "crowbar and dissipate all current within 2 seconds" strategy is probably excessive. Do any of you suspect that suddenly opening the contacts, without bleeding the cap, could cause damage to the Gecko's? If not, I will probably modify the circuit to do a slow bleed. I have a few 750 ohm wirewound resistors left over from the original Bridgeport electronics, so this would be a perfect use for one of those. Having a 750 in front of the contacts would make life very easy for them. Thanks for all the help that all of you have been able to provide.

Dan.

========================================================

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Dave Sage" <davesage12@...> wrote:
>
> I'd have to agree with Dave (I think). This whole charge dump thing seems
> excessive and un-necessary.
>

Discussion Thread

kzf817 2011-01-30 07:25:29 UTC E-stop relay welds contacts for load dump resistor David Speck 2011-01-30 07:45:47 UTC Re: [CAD_CAM_EDM_DRO] E-stop relay welds contacts for load dump resistor kzf817 2011-01-30 09:26:29 UTC Re: E-stop relay welds contacts for load dump resistor Jon Elson 2011-01-30 09:28:22 UTC Re: [CAD_CAM_EDM_DRO] E-stop relay welds contacts for load dump resistor kzf817 2011-01-30 09:47:16 UTC Re: E-stop relay welds contacts for load dump resistor David Speck 2011-01-30 11:17:30 UTC Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor kzf817 2011-01-30 11:48:21 UTC Re: E-stop relay welds contacts for load dump resistor David Speck 2011-01-30 12:21:04 UTC Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor kzf817 2011-01-30 12:53:27 UTC Re: E-stop relay welds contacts for load dump resistor David Speck 2011-01-30 13:08:45 UTC Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor kzf817 2011-01-30 14:09:18 UTC Re: E-stop relay welds contacts for load dump resistor David Speck 2011-01-30 16:51:40 UTC Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor David G. LeVine 2011-01-30 17:06:44 UTC Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor kzf817 2011-01-30 17:44:51 UTC Re: E-stop relay welds contacts for load dump resistor Earle Rich 2011-01-31 05:00:48 UTC Re: E-stop relay welds contacts for load dump resistor Dave Sage 2011-01-31 18:02:18 UTC Re: E-stop relay welds contacts for load dump resistor kzf817 2011-01-31 18:43:11 UTC Re: E-stop relay welds contacts for load dump resistor kzf817 2011-01-31 19:55:19 UTC Re: E-stop relay welds contacts for load dump resistor David Speck 2011-01-31 21:53:55 UTC Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor Les Newell 2011-02-01 02:15:41 UTC Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor Les Newell 2011-02-01 02:27:29 UTC Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor Randy Abernathy 2011-02-08 20:54:09 UTC RE: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor