Re: E-stop relay welds contacts for load dump resistor
Posted by
kzf817
on 2011-01-31 19:55:19 UTC
Dave: I was thinking about your advice, below and then double checked
Geckodrives documentation for the G320X servo drive. I did most of my
electronics enclosure assembly and wiring last winter so I had to look
over some of my schematics and documentation. Mariss specifically
states in his tech sheet for the G320X:
"IMPORTANT: Never put a switch on the DC side of the power supply!
This will damage, if not destroy, your drive!
I am sure that Mariss is speaking from experience, so this is why my
E-stop circuit is designed the way that Geckodrive specifies. Thanks!
Dan.
==================================================
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Dave Sage" <davesage12@...>
wrote:
Geckodrives documentation for the G320X servo drive. I did most of my
electronics enclosure assembly and wiring last winter so I had to look
over some of my schematics and documentation. Mariss specifically
states in his tech sheet for the G320X:
"IMPORTANT: Never put a switch on the DC side of the power supply!
This will damage, if not destroy, your drive!
I am sure that Mariss is speaking from experience, so this is why my
E-stop circuit is designed the way that Geckodrive specifies. Thanks!
Dan.
==================================================
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Dave Sage" <davesage12@...>
wrote:
>seems
> I'd have to agree with Dave (I think). This whole charge dump thing
> excessive and un-necessary.power
>
> Why not wire the E-stop relay in a normally open fashion between the
> supply output and the load.[Non-text portions of this message have been removed]
>
Discussion Thread
kzf817
2011-01-30 07:25:29 UTC
E-stop relay welds contacts for load dump resistor
David Speck
2011-01-30 07:45:47 UTC
Re: [CAD_CAM_EDM_DRO] E-stop relay welds contacts for load dump resistor
kzf817
2011-01-30 09:26:29 UTC
Re: E-stop relay welds contacts for load dump resistor
Jon Elson
2011-01-30 09:28:22 UTC
Re: [CAD_CAM_EDM_DRO] E-stop relay welds contacts for load dump resistor
kzf817
2011-01-30 09:47:16 UTC
Re: E-stop relay welds contacts for load dump resistor
David Speck
2011-01-30 11:17:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor
kzf817
2011-01-30 11:48:21 UTC
Re: E-stop relay welds contacts for load dump resistor
David Speck
2011-01-30 12:21:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor
kzf817
2011-01-30 12:53:27 UTC
Re: E-stop relay welds contacts for load dump resistor
David Speck
2011-01-30 13:08:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor
kzf817
2011-01-30 14:09:18 UTC
Re: E-stop relay welds contacts for load dump resistor
David Speck
2011-01-30 16:51:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor
David G. LeVine
2011-01-30 17:06:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor
kzf817
2011-01-30 17:44:51 UTC
Re: E-stop relay welds contacts for load dump resistor
Earle Rich
2011-01-31 05:00:48 UTC
Re: E-stop relay welds contacts for load dump resistor
Dave Sage
2011-01-31 18:02:18 UTC
Re: E-stop relay welds contacts for load dump resistor
kzf817
2011-01-31 18:43:11 UTC
Re: E-stop relay welds contacts for load dump resistor
kzf817
2011-01-31 19:55:19 UTC
Re: E-stop relay welds contacts for load dump resistor
David Speck
2011-01-31 21:53:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor
Les Newell
2011-02-01 02:15:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor
Les Newell
2011-02-01 02:27:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor
Randy Abernathy
2011-02-08 20:54:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: E-stop relay welds contacts for load dump resistor