RE: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Posted by
Andrey Lipavsky
on 2012-09-06 22:00:24 UTC
Hi Lester,
That off-white, translucent plastic, from which the collet containers are made, is likely some sort of long-chain polymer. You will be hard pressed finding a glue that will really bond to it. On the other hand, that sort of cheap plastic is rather elastic and those caps will lose their grip on the cans soon enough. As long as they come out with the cans, you can easily replace them. If you glue them in securely, you’ll have a hard time getting them to out in order to replace them. I’ve gotten bit on that previously and recommend you not make the same mistake.
Thanks,
Andrey Lipavsky
www.EssexJewelers.com
From: CAD_CAM_EDM_DRO@yahoogroups.com [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Lester Caine
Sent: Thursday, September 06, 2012 7:47 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Andrey Lipavsky wrote:
either side. The original idea was that the lids of the pots would simply stay
stuck in the hole, and you pull the top off, but it needed a better glue than
the black stuff I'd used ;)
--
Lester Caine - G8HFL
-----------------------------
Contact - http://lsces.co.uk/wiki/?page=contact
L.S.Caine Electronic Services - http://lsces.co.uk
EnquirySolve - http://enquirysolve.com/
Model Engineers Digital Workshop - http://medw.co.uk
Rainbow Digital Media - http://rainbowdigitalmedia.co.uk
[Non-text portions of this message have been removed]
That off-white, translucent plastic, from which the collet containers are made, is likely some sort of long-chain polymer. You will be hard pressed finding a glue that will really bond to it. On the other hand, that sort of cheap plastic is rather elastic and those caps will lose their grip on the cans soon enough. As long as they come out with the cans, you can easily replace them. If you glue them in securely, you’ll have a hard time getting them to out in order to replace them. I’ve gotten bit on that previously and recommend you not make the same mistake.
Thanks,
Andrey Lipavsky
www.EssexJewelers.com
From: CAD_CAM_EDM_DRO@yahoogroups.com [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Lester Caine
Sent: Thursday, September 06, 2012 7:47 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Andrey Lipavsky wrote:
> Hi Lester,The block is a 6mm offcut of perspex, with the two colour plastic stuck on
>
> What is the black, gummy-looking compound at the bottom of the wells?
either side. The original idea was that the lids of the pots would simply stay
stuck in the hole, and you pull the top off, but it needed a better glue than
the black stuff I'd used ;)
--
Lester Caine - G8HFL
-----------------------------
Contact - http://lsces.co.uk/wiki/?page=contact
L.S.Caine Electronic Services - http://lsces.co.uk
EnquirySolve - http://enquirysolve.com/
Model Engineers Digital Workshop - http://medw.co.uk
Rainbow Digital Media - http://rainbowdigitalmedia.co.uk
[Non-text portions of this message have been removed]
Discussion Thread
Peter
2012-09-05 20:43:39 UTC
Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Dan Field
2012-09-06 10:19:20 UTC
Re: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Peter Homann
2012-09-06 14:43:52 UTC
Re: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Lester Caine
2012-09-06 15:03:22 UTC
Re: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Peter Homann
2012-09-06 16:03:09 UTC
Re: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Andrey Lipavsky
2012-09-06 16:24:14 UTC
RE: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Lester Caine
2012-09-06 16:47:24 UTC
Re: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Andrey Lipavsky
2012-09-06 22:00:24 UTC
RE: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders
Lester Caine
2012-09-06 22:47:09 UTC
Re: [CAD_CAM_EDM_DRO] Too lRack Project for ER16 Collet adaptors and 1" Arbor Tool holders