CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] move error in MACH3

Posted by Ron Thompson
on 2012-12-01 21:14:21 UTC
On 12/1/2012 7:03 PM, ebiz_59 wrote:
> We have a Grizzly mini mill with 276 ozin steppers, Gecko 540 (24v)
> supply, and MACH3. We are making egg shaped circles and want them to
> be round.
>
> We have calibrated the axis's and they are both right on (and very
> similar steps per inch numbers of 15984.xxx and 16000.xxxx. And we
> have redone the backlash, (home made plastic nuts on ACME threads) X
> was 0.001 and Y was 0.009. And we have restarted MACH several times to
> and confirmed that the settings have changed.
>
> HOWEVER, when we go to MDI in MACH and tell the X axis to move 0.5",
> it actually moves 0.455" - and is pretty repeatable (+/- a thou or
> sometimes 2).
>
> Interestingly (and frustratingly) when we do an 8 hole bolt pattern,
> and measure the major and minor axis's and subtract the smaller from
> the larger, we get a difference of 0.046"... note that 0.5-0.455 =
> 0.046. We must have some setting messed up, but just can't find it.
>
> Any help would be great!
> Thanks,
> Chuck
Sounds like your steps per inch isn't right.
On the settings tab, use the axis calibration just above the reset
button. Try to use the longest move you can, as it will be more accurate
than a short move.

--


Ron Thompson
On the Beautiful Florida Space Coast, right beside the Kennedy Space Center, USA

Think, Draw, Print. 3D printers ROCK!

http://www.plansandprojects.com/My%20Machines/PrusaMendel2012-1/

http://www.plansandprojects.com My hobby pages are here:
http://www.plansandprojects.com/My%20Machines/

Visit the castinghobby FAQ:
http://castinghobbyfaq.bareboogerhost.com/

Discussion Thread

ebiz_59 2012-12-01 16:03:11 UTC move error in MACH3 Ron Thompson 2012-12-01 21:14:21 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 chuck merja 2012-12-01 22:55:20 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 Dan Mauch 2012-12-02 05:47:27 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 jeremy youngs 2012-12-02 10:13:12 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 Jon Elson 2012-12-02 11:02:59 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 chuck merja 2012-12-03 07:45:14 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 Jon Elson 2012-12-03 10:21:30 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 chuck merja 2012-12-04 09:08:36 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 Drew Rogge 2012-12-04 09:21:09 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 Ron Thompson 2012-12-04 09:23:20 UTC Re: [CAD_CAM_EDM_DRO] move error in MACH3 ScottT 2012-12-04 13:31:59 UTC Re: move error in MACH3 Dan Mauch 2012-12-04 17:54:26 UTC RE: [CAD_CAM_EDM_DRO] move error in MACH3 Norman Bain 2012-12-04 17:55:08 UTC Re: [CAD_CAM_EDM_DRO] Re: move error in MACH3