Re: [CAD_CAM_EDM_DRO] CNC Engraving
Posted by
Gary Click
on 2013-05-23 12:17:23 UTC
5140 RPMS
5 IPM
.008"-.010"Depth of Cut
________________________________
From: Jack McKie <freshwatermodels@...>
To: "CAD_CAM_EDM_DRO@yahoogroups.com" <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thu, May 23, 2013 2:01:19 PM
Subject: Re: [CAD_CAM_EDM_DRO] CNC Engraving
What feed rate ipm, are you using?
________________________________
From: Gary Click <garyclick@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Thursday, May 23, 2013 2:05 PM
Subject: Re: [CAD_CAM_EDM_DRO] CNC Engraving
I use them extensively running on a Tormach 1100. I use primarily the .3mm
30deg. cutter I believe but I need to check that. Current we are using these
cutters to engrave the product name and Made In USA on Ductile Iron Castings.
The spindle is run at 5140rpms (max available), depth of cut .008" to .010" and
5ipm. The text is .4" tall and in Helvetica Font. Total length of cut by summing
the leters is about 15" and takes 2.6 minutes. The result looks sharp and crisp
and really makes the finished casting stand out.
I bought the cutters from a Chinese seller and they were $1.76 delivered and
arrived in about 10 days via China Post. We have run about 500 casting and I was
not expecting these to last since they are needle sharp and should be run at
more like 20,000rpms, so I ordered 50 cutters. So far we have used three and
the fourth is in the spindle for 500 castings and a couple hundred other parts..
I have also used these in G10-FRP Composite which is by far the toughest
material on tool life that we cut, steel and brass. Without a high speed spindle
the feedrate is slow but the results are very good.
nitewatchman
________________________________
From: Jack <mailto:freshwatermodels%40yahoo.com>
To: mailto:CAD_CAM_EDM_DRO%40yahoogroups.com
Sent: Thu, May 23, 2013 12:17:58 PM
Subject: [CAD_CAM_EDM_DRO] CNC Engraving
I want to make a couple of name plates for a model locomotive. They are made of
brass and tiny. I have been looking at pointed carbide "engraving" bits from
China on eBay. I assume these are intended for making ciruit boards. I am
wondering if anyone has had experience using these? The one I am considering
using is about .2mm which I beleive works out to about .008"
Any comments or insite would be appreciated.
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
Reply via web post Reply to sender Reply to group Start a New Topic Messages
in this topic (9)
Recent Activity: * New Members 8
Visit Your Group
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you
have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop%c2%a0%c2%a0 I consider this to be a sister
site to the CCED group, as many of the same members are there, for OT subjects,
that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T
POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Switch to: Text-Only, Daily Digest • Unsubscribe • Terms of Use • Send us
Feedback
.
[Non-text portions of this message have been removed]
5 IPM
.008"-.010"Depth of Cut
________________________________
From: Jack McKie <freshwatermodels@...>
To: "CAD_CAM_EDM_DRO@yahoogroups.com" <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thu, May 23, 2013 2:01:19 PM
Subject: Re: [CAD_CAM_EDM_DRO] CNC Engraving
What feed rate ipm, are you using?
________________________________
From: Gary Click <garyclick@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Thursday, May 23, 2013 2:05 PM
Subject: Re: [CAD_CAM_EDM_DRO] CNC Engraving
I use them extensively running on a Tormach 1100. I use primarily the .3mm
30deg. cutter I believe but I need to check that. Current we are using these
cutters to engrave the product name and Made In USA on Ductile Iron Castings.
The spindle is run at 5140rpms (max available), depth of cut .008" to .010" and
5ipm. The text is .4" tall and in Helvetica Font. Total length of cut by summing
the leters is about 15" and takes 2.6 minutes. The result looks sharp and crisp
and really makes the finished casting stand out.
I bought the cutters from a Chinese seller and they were $1.76 delivered and
arrived in about 10 days via China Post. We have run about 500 casting and I was
not expecting these to last since they are needle sharp and should be run at
more like 20,000rpms, so I ordered 50 cutters. So far we have used three and
the fourth is in the spindle for 500 castings and a couple hundred other parts..
I have also used these in G10-FRP Composite which is by far the toughest
material on tool life that we cut, steel and brass. Without a high speed spindle
the feedrate is slow but the results are very good.
nitewatchman
________________________________
From: Jack <mailto:freshwatermodels%40yahoo.com>
To: mailto:CAD_CAM_EDM_DRO%40yahoogroups.com
Sent: Thu, May 23, 2013 12:17:58 PM
Subject: [CAD_CAM_EDM_DRO] CNC Engraving
I want to make a couple of name plates for a model locomotive. They are made of
brass and tiny. I have been looking at pointed carbide "engraving" bits from
China on eBay. I assume these are intended for making ciruit boards. I am
wondering if anyone has had experience using these? The one I am considering
using is about .2mm which I beleive works out to about .008"
Any comments or insite would be appreciated.
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
Reply via web post Reply to sender Reply to group Start a New Topic Messages
in this topic (9)
Recent Activity: * New Members 8
Visit Your Group
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you
have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop%c2%a0%c2%a0 I consider this to be a sister
site to the CCED group, as many of the same members are there, for OT subjects,
that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T
POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Switch to: Text-Only, Daily Digest • Unsubscribe • Terms of Use • Send us
Feedback
.
[Non-text portions of this message have been removed]
Discussion Thread
Cletus Berkeley
2004-10-13 19:16:52 UTC
CNC Engraving
caudlet
2004-10-13 20:03:16 UTC
Re: CNC Engraving
uyu3
2004-10-14 17:20:18 UTC
Re: CNC Engraving
Jack
2013-05-23 10:11:22 UTC
CNC Engraving
Dan Mauch
2013-05-23 10:40:55 UTC
RE: [CAD_CAM_EDM_DRO] CNC Engraving
Dan Mauch
2013-05-23 10:47:54 UTC
RE: [CAD_CAM_EDM_DRO] CNC Engraving
Gary Click
2013-05-23 11:05:54 UTC
Re: [CAD_CAM_EDM_DRO] CNC Engraving
Jack McKie
2013-05-23 11:39:18 UTC
Re: [CAD_CAM_EDM_DRO] CNC Engraving
Jack McKie
2013-05-23 11:50:13 UTC
Re: [CAD_CAM_EDM_DRO] CNC Engraving
Stephen Muscato
2013-05-23 11:55:26 UTC
Re: [CAD_CAM_EDM_DRO] CNC Engraving
Gary Click
2013-05-23 12:17:23 UTC
Re: [CAD_CAM_EDM_DRO] CNC Engraving
Dan Mauch
2013-05-23 12:51:56 UTC
RE: [CAD_CAM_EDM_DRO] CNC Engraving
Roland Jollivet
2013-05-24 09:29:37 UTC
Re: [CAD_CAM_EDM_DRO] CNC Engraving
skullworks
2013-05-24 13:11:44 UTC
Re: CNC Engraving