RE: [CAD_CAM_EDM_DRO] G-code interpreters in DOS?
Posted by
Randy Gordon-Gilmore
on 2000-11-07 22:12:00 UTC
At 06:23 PM 11/7/00 -0700, Tim wrote:
you've put into your installation procedure!), which omission I intend to
rectify now. Thank you.
CNCPro does look very impressive. I've downloaded the demo version, and it
gives 20 moves per session (just enough to do maybe a little facing or
maybe some minor pocketing, depending on how it counts moves...) I will
try it out when I finish retrofitting the mill.
I will seriously weigh your advice. EMC does look like a powerful piece of
software (even though I have probably the minimum system imaginiable--a
Sherline mill about to be converted with steppers) and, as a taxpayer I
definitely wouldn't look askance at getting some tangible benefit from my
"contributions!" :-)
Best regards,
Randy
Randy Gordon-Gilmore ,----.___________ ______________ _________________
ProtoTrains // = = === == || == == == = || == == == = == =|
Rio Vista, CA, USA /-O==O------------o==o------------o==o-----------o==o-'
zephyrus@... http://www.rickadee.net/~zephyrus
>The script should look just like a DOS batch file to you.[snip]
>OTOH, it is sounding like you may want to take a look at CNCPro. TheTim, I neglected to thank you for your reply (and the obvious hard work
you've put into your installation procedure!), which omission I intend to
rectify now. Thank you.
CNCPro does look very impressive. I've downloaded the demo version, and it
gives 20 moves per session (just enough to do maybe a little facing or
maybe some minor pocketing, depending on how it counts moves...) I will
try it out when I finish retrofitting the mill.
I will seriously weigh your advice. EMC does look like a powerful piece of
software (even though I have probably the minimum system imaginiable--a
Sherline mill about to be converted with steppers) and, as a taxpayer I
definitely wouldn't look askance at getting some tangible benefit from my
"contributions!" :-)
Best regards,
Randy
Randy Gordon-Gilmore ,----.___________ ______________ _________________
ProtoTrains // = = === == || == == == = || == == == = == =|
Rio Vista, CA, USA /-O==O------------o==o------------o==o-----------o==o-'
zephyrus@... http://www.rickadee.net/~zephyrus
Discussion Thread
Randy Gordon-Gilmore
2000-11-07 16:51:49 UTC
G-code interpreters in DOS?
Tim Goldstein
2000-11-07 17:10:52 UTC
RE: [CAD_CAM_EDM_DRO] G-code interpreters in DOS?
Randy Gordon-Gilmore
2000-11-07 17:42:29 UTC
RE: [CAD_CAM_EDM_DRO] G-code interpreters in DOS?
ballendo@y...
2000-11-07 21:38:36 UTC
G-code interpreters in DOS?
Randy Gordon-Gilmore
2000-11-07 22:12:00 UTC
RE: [CAD_CAM_EDM_DRO] G-code interpreters in DOS?
Randy Gordon-Gilmore
2000-11-07 22:39:52 UTC
Re: [CAD_CAM_EDM_DRO] G-code interpreters in DOS?
ballendo@y...
2000-11-07 23:06:36 UTC
Re: G-code interpreters in DOS?
Hugh Currin
2000-11-08 10:02:20 UTC
RE: G-code interpreters in DOS?
Tim Goldstein
2000-11-08 12:53:35 UTC
RE: [CAD_CAM_EDM_DRO] RE: G-code interpreters in DOS?