CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] BDI EMC Announcement

on 2001-04-02 06:00:29 UTC
Hola amigos vean que ha entrado estos dias,
¡¡¡¡ si esto no es una excelente noticia !!!!
atentmente
Sven Peter

Paul wrote:

> Hi Folks
>
> After several months of work - And quite a few late nights.
> The Brain Dead Install for EMC is finally ready. It will be available at NAMES
> at the end of the month for $10 per CD. (maybe a little less if I can get
> sufficient quantities burnt in time).
>
> The minimum recommended hardware is as follows :
>
> Pentium class processor - Not WinChip
> 16Mb Ram
> 420Mb IDE Hard drive - 1Gb for a programmers install
> CDROM drive - preferrably one that you can boot from.
> Colour graphics card
> Colour monitor that can do 800x600 or better
> Plus a mouse and keyboard.
> 1.4Mb floppy drive is optional, as is a network card.
>
> There is no support for SCSI drives USB or sound.
>
> The kernel is built from a virgin 2.2.18 and rtlinux 3.0 sources. Also
> included is the sources for the latest 2.4.2 kernel.
>
> A typical install will autodetect most standard hardware and from start to
> finish takes about 30 minutes. No work is involved in patching or compiling
> source code unless you want to.
>
> To reserve your copy, please email me, paul.corner@... with
> RESERVE BDI EMC in the subject header.
>
> Ray, rehenry@... will be the main point of contact for anyone wishing to
> recieve a copy via mail in the USA. These will be available in May, when I
> should be in a position to handle enquiries from the rest of the world.
>
> Regards, Paul.
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
>

Discussion Thread

Paul 2001-04-01 03:40:02 UTC BDI EMC Announcement Tom Eldredge 2001-04-01 06:45:23 UTC Re: [CAD_CAM_EDM_DRO] BDI EMC Announcement Robin S. 2001-04-01 08:42:01 UTC Re: BDI EMC Announcement Paul 2001-04-01 09:59:05 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI EMC Announcement Ray 2001-04-01 19:42:11 UTC Re: Re: BDI EMC Announcement Jon Elson 2001-04-01 23:30:45 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI EMC Announcement Deon Styger 2001-04-02 04:39:54 UTC RE: BDI EMC Announcement Sven Peter, TAD S.A. 2001-04-02 06:00:29 UTC Re: [CAD_CAM_EDM_DRO] BDI EMC Announcement Paul 2001-04-02 12:32:14 UTC Re: BDI Announcement Sven Peter, TAD S.A. 2001-04-02 17:20:49 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI Announcement Tom Eldredge 2001-04-03 04:13:34 UTC Re: [CAD_CAM_EDM_DRO] RE: BDI EMC Announcement