Re: [CAD_CAM_EDM_DRO] RE: BDI EMC Announcement
Posted by
Tom Eldredge
on 2001-04-03 04:13:34 UTC
Paul,
I also wish to thank you. I plan to get a CD at Names, (I hope you send
enough-you may be surprised at how many will want one). I am very excited
about this.
Tom Eldredge
I also wish to thank you. I plan to get a CD at Names, (I hope you send
enough-you may be surprised at how many will want one). I am very excited
about this.
Tom Eldredge
----- Original Message -----
From: Deon Styger <deons@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Monday, April 02, 2001 6:41 AM
Subject: [CAD_CAM_EDM_DRO] RE: BDI EMC Announcement
> Paul,
>
> On behalf of the group, let me congratulate you on your effort to make
this
> cd available. I think that you have done us all a big favour. Something
> like this is long overdue. Hopefully more of us "brain dead idiots" will
be
> able to use EMC without going "bonkers" in the process.
>
> Deon Styger
>
> -----Original Message-----
>
> >Hi Folks
>
> >After several months of work - And quite a few late nights.
> >The Brain Dead Install for EMC is finally ready. It will be available at
> NAMES
> >at the end of the month for $10 per CD. (maybe a little less if I can get
> >sufficient quantities burnt in time).
>
> >The minimum recommended hardware is as follows :
>
> >Pentium class processor - Not WinChip
> >16Mb Ram
> >420Mb IDE Hard drive - 1Gb for a programmers install
> >CDROM drive - preferrably one that you can boot from.
> >Colour graphics card
> >Colour monitor that can do 800x600 or better
> >Plus a mouse and keyboard.
> >1.4Mb floppy drive is optional, as is a network card.
>
> >There is no support for SCSI drives USB or sound.
>
> >The kernel is built from a virgin 2.2.18 and rtlinux 3.0 sources. Also
> >included is the sources for the latest 2.4.2 kernel.
>
> >A typical install will autodetect most standard hardware and from start
to
> >finish takes about 30 minutes. No work is involved in patching or
compiling
> >source code unless you want to.
>
> >To reserve your copy, please email me, paul.corner@... with
> >RESERVE BDI EMC in the subject header.
>
> >Ray, rehenry@... will be the main point of contact for anyone wishing
to
> >recieve a copy via mail in the USA. These will be available in May, when
I
> >should be in a position to handle enquiries from the rest of the world.
>
> >Regards, Paul.
>
>
>
> ________________________________________________________________________
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
Paul
2001-04-01 03:40:02 UTC
BDI EMC Announcement
Tom Eldredge
2001-04-01 06:45:23 UTC
Re: [CAD_CAM_EDM_DRO] BDI EMC Announcement
Robin S.
2001-04-01 08:42:01 UTC
Re: BDI EMC Announcement
Paul
2001-04-01 09:59:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: BDI EMC Announcement
Ray
2001-04-01 19:42:11 UTC
Re: Re: BDI EMC Announcement
Jon Elson
2001-04-01 23:30:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: BDI EMC Announcement
Deon Styger
2001-04-02 04:39:54 UTC
RE: BDI EMC Announcement
Sven Peter, TAD S.A.
2001-04-02 06:00:29 UTC
Re: [CAD_CAM_EDM_DRO] BDI EMC Announcement
Paul
2001-04-02 12:32:14 UTC
Re: BDI Announcement
Sven Peter, TAD S.A.
2001-04-02 17:20:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: BDI Announcement
Tom Eldredge
2001-04-03 04:13:34 UTC
Re: [CAD_CAM_EDM_DRO] RE: BDI EMC Announcement