RE: [CAD_CAM_EDM_DRO] Simple DRO new idea

Can you be more specific as to the number of the hall effect transistor, and
have you managed to get anything working yet.

Cheers

Mark

-----Original Message-----
From: M. SHABBIR [mailto:shabm@...]
Sent: 05 September 2001 03:23
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Simple DRO new idea


ok thanks
i think u have also tried to using stepper motor or stepper rooter magnet.


shabbir


At 10:46 PM 9/3/01 +0000, you wrote:0

>"M. SHABBIR" wrote:
>
>> hi
>> u can find ring magnet in back of audio speaker.
>>
>> shabbir
>>
>> At 02:26 PM 9/2/01 -0600, you wrote:
>> >Scott
>> >I am working on a very simple dro using a special purpose Hall effect

sensor

>> >and a simple up down counter connected to a 8 digit led. It would work

as

>> >follows
>> >a linear magnet strip or a ring magnet with alternating north and south
>
>The ring shaped magnet it a speaker has one pole in the center, and one

pole

>on the OD (some fold the design, so each face is a pole). This won't work
>as a magnetic encoder, since the poles don't move when it is rotated.
>A 2-pole motor with a ring magnet only has 2 poles for one revolution,
>so that may still not work well for your application. Floppy drive motors
>from the ones with the motor in the hub usually have more poles, and may
>have a tach ring that has many poles per rev. These are pretty large
>diameter, however.
>
>Jon
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/



_____________________________________________________________________
***********************************************************************
This message has been checked for all known viruses by the
E-mail Virus Protection service, powered by MessageLabs.
***********************************************************************

***********************************************************************
This message has been checked for all known viruses by the
E-mail Virus Protection service, powered by MessageLabs.
***********************************************************************