RE: [CAD_CAM_EDM_DRO] Simple DRO new idea update
Posted by
HighTech
on 2001-09-05 09:30:53 UTC
Mark
So far Jon's idea of using floppy drive motor is working it has a ring
magnet
in it. I tested the hall sensor on the scope it is making good square waves.
I
don't know if this ring is going to have enough of the north south magnets.
I need
a ring that spaces them 3mm wide example north 3mm, south 3mmm, north 3mm,
south 3mm
and so on. I don't have all the electronics yet and still have to make a pc
board.
To answer your question it takes only 1 hall effect per axis. Costs
approximately
$3.00 to $4.00 each, depends on where you can find them and quantity
ordered.
Derek B.
Can you be more specific as to the number of the hall effect transistor, and
have you managed to get anything working yet.
Cheers
Mark
Floppy drive motors
So far Jon's idea of using floppy drive motor is working it has a ring
magnet
in it. I tested the hall sensor on the scope it is making good square waves.
I
don't know if this ring is going to have enough of the north south magnets.
I need
a ring that spaces them 3mm wide example north 3mm, south 3mmm, north 3mm,
south 3mm
and so on. I don't have all the electronics yet and still have to make a pc
board.
To answer your question it takes only 1 hall effect per axis. Costs
approximately
$3.00 to $4.00 each, depends on where you can find them and quantity
ordered.
Derek B.
Can you be more specific as to the number of the hall effect transistor, and
have you managed to get anything working yet.
Cheers
Mark
Floppy drive motors
>from the ones with the motor in the hub usually have more poles, and may__
>have a tach ring that has many poles per rev. These are pretty large
>diameter, however.
>
>Jon
>
>
Discussion Thread
Scott Riddle
2001-09-02 08:44:49 UTC
Simple DRO
Doug Harrison
2001-09-02 09:05:03 UTC
Re: [CAD_CAM_EDM_DRO] Simple DRO
Art Eckstein
2001-09-02 11:46:57 UTC
Re: [CAD_CAM_EDM_DRO] Simple DRO
wanliker@a...
2001-09-02 12:17:14 UTC
Re: [CAD_CAM_EDM_DRO] Simple DRO
HighTech
2001-09-02 13:20:49 UTC
RE: [CAD_CAM_EDM_DRO] Simple DRO new idea
Art Eckstein
2001-09-02 13:40:05 UTC
Re: [CAD_CAM_EDM_DRO] Simple DRO
M. SHABBIR
2001-09-03 11:38:05 UTC
RE: [CAD_CAM_EDM_DRO] Simple DRO new idea
cncdxf@a...
2001-09-03 12:01:38 UTC
Re: Simple DRO new idea
Jon Elson
2001-09-03 15:42:19 UTC
Re: [CAD_CAM_EDM_DRO] Simple DRO new idea
Alan Marconett KM6VV
2001-09-04 10:54:28 UTC
Re: [CAD_CAM_EDM_DRO] Simple DRO new idea
M. SHABBIR
2001-09-04 19:36:28 UTC
Re: [CAD_CAM_EDM_DRO] Simple DRO new idea
Mark Taft
2001-09-05 00:55:16 UTC
RE: [CAD_CAM_EDM_DRO] Simple DRO new idea
dlantz@a...
2001-09-05 04:56:44 UTC
RE: [CAD_CAM_EDM_DRO] Simple DRO new idea
HighTech
2001-09-05 09:30:53 UTC
RE: [CAD_CAM_EDM_DRO] Simple DRO new idea update
Jon Elson
2001-09-05 10:41:35 UTC
Re: [CAD_CAM_EDM_DRO] Simple DRO new idea
M. SHABBIR
2001-09-06 20:13:31 UTC
RE: [CAD_CAM_EDM_DRO] Simple DRO new idea