CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Gecko G340 Smoothness

Posted by Andy Olney
on 2001-09-18 01:18:18 UTC
Tim -thanks for the reply. I am still a little confused after reading more
of the manual. Say I send the drive 1 step and I am running in the 5X mode.
The drive must try to move 5 encoder counts for that single step.

I guess I will have to play with it to find out. Andy

-----Original Message-----
From: Tim [mailto:timg@...]
Sent: Monday, September 17, 2001 2:13 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: RE: [CAD_CAM_EDM_DRO] Gecko G340 Smoothness


First off while the G3X0 drives are servos because they are driven from
the computer in distinct increments (steps) the motion at very low feed
rates will look just like a stepper (meaning that if you signal a 1 step
move it will get there as fast as it can with no interpretation for
velocity). With that said if you decrease the distance moved in a single
step you can then get smoother motion by calling 5 small steps timed at
even intravals than by calling for 1 step that moves 5 times as far.

This is simplifying it some as Mariss had made the drive to spread the
generated steps over a certain window and once you get over some unknown
speed the steps will blur together and you will also likely be driving
with a continual error signal so the motor will not stop, start, stop,
start like it will at very slow feeds.

Tim
[Denver, CO]

> -----Original Message-----
>
>
> Have my mill moving again with the Gecko drives and as usual have a
> question.
>
> I have some motor noise at low speeds (5 ipm), more than at the
> rapids I am getting. (80 ipm) I can see the table screws pause as
> they turn (very short stop starts) so I may have some acme screw -
> bronze nut stop/start friction. I looks like a stepper motion.
>
> More info:
> The drives are in the 5x setting and about 4000 steps/in so the
> encoders are putting out about 20000 steps/inch.
>
> Any one (Tim? Mariss?) have an opinion on whether changing to the 1x
> mode would make the motion smoother, assuming I can coerce EMC into
> pushing out the steps fast enough?
>
> P.S. The burn table conversion ( EMC and Dan Mauch's G340 servo box )
> I have previously posted about is working well!
>
> Andy Olney
> andy@...
> Grizzly G1004 small knee mill conversion
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

andy@o... 2001-09-17 13:28:00 UTC Gecko G340 Smoothness info.host@b... 2001-09-17 18:31:42 UTC Re: [CAD_CAM_EDM_DRO] Gecko G340 Smoothness Tim 2001-09-17 19:04:39 UTC RE: [CAD_CAM_EDM_DRO] Gecko G340 Smoothness Andy Olney 2001-09-18 01:15:43 UTC RE: [CAD_CAM_EDM_DRO] Gecko G340 Smoothness Andy Olney 2001-09-18 01:18:18 UTC RE: [CAD_CAM_EDM_DRO] Gecko G340 Smoothness