RE: [CAD_CAM_EDM_DRO] Technique for parting a part
Posted by
Ethan Vos
on 2001-10-26 09:47:52 UTC
Are you milling or turning this part?
Ethan
-----Original Message-----
From: Rob [SMTP:robv@...]
Sent: Friday, October 26, 2001 12:43 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Technique for parting a part
While I'm still very much a newbie, I have a question I just can't
seem to figure out.
If you start with a billet of say aluminum and you want to cut out a
part, what are the stratagies for removing the part from the excess
stock material? Should I program my NC code to cut all the way
through into some scrap material?
Also - how about cutting 2 sides of a part? Would you generate NC
code to cut the first side, then flip the part and run NC code to
cut the other side?
Thanks everyone, you have been most helpful in getting me up and
running in the world of CNC mills and lathes.
Rob
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Ethan
-----Original Message-----
From: Rob [SMTP:robv@...]
Sent: Friday, October 26, 2001 12:43 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Technique for parting a part
While I'm still very much a newbie, I have a question I just can't
seem to figure out.
If you start with a billet of say aluminum and you want to cut out a
part, what are the stratagies for removing the part from the excess
stock material? Should I program my NC code to cut all the way
through into some scrap material?
Also - how about cutting 2 sides of a part? Would you generate NC
code to cut the first side, then flip the part and run NC code to
cut the other side?
Thanks everyone, you have been most helpful in getting me up and
running in the world of CNC mills and lathes.
Rob
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
Rob
2001-10-26 09:43:34 UTC
Technique for parting a part
Ethan Vos
2001-10-26 09:47:52 UTC
RE: [CAD_CAM_EDM_DRO] Technique for parting a part
joevicar3@h...
2001-10-26 10:12:38 UTC
Re: Technique for parting a part
Rob
2001-10-26 10:35:38 UTC
Re: Technique for parting a part
npalen@n...
2001-10-26 19:48:44 UTC
Re: Technique for parting a part
Smoke
2001-10-26 20:53:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Technique for parting a part
Jon Elson
2001-10-26 23:07:16 UTC
Re: [CAD_CAM_EDM_DRO] Technique for parting a part
Jon Elson
2001-10-26 23:21:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Technique for parting a part
Ian Wright
2001-10-27 02:11:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Technique for parting a part
npalen@n...
2001-10-27 08:34:52 UTC
Re: Technique for parting a part