CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Help! Linux problem

Posted by Jon Elson
on 2001-12-16 22:47:07 UTC
Jack Ensor wrote:

> > ....Snip
> >
> > Specifically, the command
> >
> > more /proc/version
> >
> > will give you the info you want. Since you aren't familiar with what is
> > in the /proc pseudodirectory, you should do
> >
> > ls /proc
> >
> > and see all the interesting reports on the system that are in there. You
> > can pretty much ignore the numbered ones, but the ones with obvious
> > names contain all sorts of information on the system configuration.
> > Skip /proc/kcore, this is a window into the system memory. more
> > allows you to see the file one page at a time, although most of these
> > are small.
> >
> > Jon
>
> Jon -
>
> When I enter the command you mention above specifically:
>
> Skip /proc/kcore
>
> I get:
>
> bash: Skip: command not found
>
> Should it be there from a BDI install?

Oh, now I see what you were talking about. when he says skip, he
means don't do it, ie do not enter more /proc/core, as you will get a
listing that runs on for approximately a million pages, a complete
memory dump of your system in hexadecimal. There is no skip
command. Note that linux is case sensitive, ie More is not the
same as more, and could be a completely different command.
Most Linux commands are all lower case.

Jon

Discussion Thread

don.pat.brock@p... 2001-09-08 12:41:59 UTC Help! Linux problem Eric Keller 2001-09-08 13:31:58 UTC Re: [CAD_CAM_EDM_DRO] Help! Linux problem Jon Elson 2001-09-08 21:58:20 UTC Re: [CAD_CAM_EDM_DRO] Help! Linux problem Earl 2001-09-09 01:57:32 UTC Re: Help! Linux problem Donald Brock 2001-09-09 02:59:27 UTC Re: Help! Linux problem rfs@c... 2001-09-09 19:10:25 UTC Re: Help! Linux problem Jon Elson 2001-09-09 21:46:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Help! Linux problem Ray 2001-09-10 07:00:24 UTC Re: Re: Help! Linux problem jensor@q... 2001-09-10 19:02:03 UTC Re: Help! Linux problem Doug Fortune 2001-09-10 20:36:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Help! Linux problem Jon Elson 2001-09-10 21:57:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Help! Linux problem Jack Ensor 2001-12-16 18:15:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Help! Linux problem Tim Goldstein 2001-12-16 19:47:56 UTC Keyboard for CNC Gail & Bryan Harries 2001-12-16 22:28:39 UTC RE: [CAD_CAM_EDM_DRO] Keyboard for CNC Jon Elson 2001-12-16 22:43:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Help! Linux problem Jon Elson 2001-12-16 22:47:07 UTC Re: [CAD_CAM_EDM_DRO] Re: Help! Linux problem Tim Goldstein 2001-12-16 22:48:26 UTC RE: [CAD_CAM_EDM_DRO] Keyboard for CNC stevenson_engineers 2001-12-17 00:11:52 UTC Re: Keyboard for CNC Tim Goldstein 2001-12-17 06:58:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Keyboard for CNC