CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: shielded cable

Posted by Peter Seddon
on 2001-12-20 07:05:38 UTC
I would never run power and feedback wires in the same cable as the chances
of problems are considerably increased.

Regards Peter


----- Original Message -----
From: "npp67420" <npalen@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, December 20, 2001 1:13 PM
Subject: [CAD_CAM_EDM_DRO] Re: shielded cable


> Doug--Sounds great! I would love to run the motor wires in the same
> cable as the encoder leads. You've found this to not be problem with
> interference?
> I'm feeding into a DB15 on the Kerr Engineering PICSERVO
> step/direction adapters. Any help is appreciated.
> Thanks
> Nelson
>
>
>
>
> --- In CAD_CAM_EDM_DRO@y..., Doug Fortune <pentam@h...> wrote:
> > npp67420 wrote:
> > >
> > > Hello all. Wondering if anyone might know of a mail order source
> for
> > > small quantity of shielded cable? Needing 22 or 24 gauge with
> four
> > > twisted pair in a flexible cable for connecting axis encoders to
> the
> > > drives.
> >
> > I have 6 pair 20 AWG (individually shielded and drained) wire
> > (its not on my webpage yet). 20 gauge is good for 7 amps
> continuous
> > and so I use it not only for encoder signals, but also singly
> > (with Gecko 2xx stepper drivers) and in pairs with Gecko 3xx
> > servo drivers. Over Christmas I'll try to get it (and the
> > 12 pin connectors) onto the web page.
> >
> > My reasons for using 6 pair is spelled out in a previous post:
> > http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/message/32734
> >
> > Send me your adress and I'll mail you a sample. It's .4" dia
> > so its not skinny cable.
> >
> > Doug Fortune
> > http://www.cncKITS.com
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
>

Discussion Thread

npp67420 2001-12-19 22:26:00 UTC shielded cable Doug Fortune 2001-12-19 23:00:05 UTC Re: [CAD_CAM_EDM_DRO] shielded cable npp67420 2001-12-20 05:13:35 UTC Re: shielded cable Peter Seddon 2001-12-20 07:05:38 UTC Re: [CAD_CAM_EDM_DRO] Re: shielded cable chewy8833 2001-12-20 07:22:22 UTC Re: shielded cable Drew Rogge 2001-12-20 07:57:23 UTC Re: [CAD_CAM_EDM_DRO] Re: shielded cable