Re: [CAD_CAM_EDM_DRO] Re: Thanks Mariss/Where are you!
Posted by
Rich D.
on 2002-01-11 16:38:16 UTC
Mariss, Paul,
Take a look at most KB Electronics DC drives. Full wave Triac rectified
line voltage. No transformers. I have several in use here.
No problem for me.
Follow the directions supplied.
RichD
sprooney797 wrote:
Take a look at most KB Electronics DC drives. Full wave Triac rectified
line voltage. No transformers. I have several in use here.
No problem for me.
Follow the directions supplied.
RichD
sprooney797 wrote:
>
> Mariss Wrote:
> > (3) Sure as God made little green apples someone will run it off of
> > rectified 115VAC, kill himself and more lawyers will become rich at
> > my expense.
>
> Mariss, running from a rectified 115vac source sounds very appealing,
> and I must admit that is why I would like a drive that is rated to
> handle the higher voltage.
>
> If the circuit is properly grounded and fused, where is the danger in
> doing this? I believe many of the industrial servo drives work off of
> a rectified AC source.
>
> Would the use of an isolation transformer make it any safer?
>
> Or is the risk because of the use of home-made cables and cobbled up
> control boxes?
>
> Just curious as I'd love to do away with the large DC power supplies.
>
> Sincerely,
>
> Paul Rooney
Discussion Thread
Multi-Volti Devices (Murray)
2002-01-10 05:49:02 UTC
Thanks Mariss
chewy8833
2002-01-10 15:40:10 UTC
Re: Thanks Mariss/Where are you!
mariss92705
2002-01-10 16:47:41 UTC
Re: Thanks Mariss/Where are you!
unterhausen
2002-01-10 18:46:08 UTC
Re: Thanks Mariss/Where are you!
Carol & Jerry Jankura
2002-01-10 18:56:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: Thanks Mariss/Where are you!
mariss92705
2002-01-10 19:09:43 UTC
Re: Thanks Mariss/Where are you!
mariss92705
2002-01-10 19:35:03 UTC
Re: Thanks Mariss/Where are you!
Art Fenerty
2002-01-11 09:29:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks Mariss/Where are you!
ccs@m...
2002-01-11 10:09:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks Mariss/Where are you!
sprooney797
2002-01-11 15:32:22 UTC
Re: Thanks Mariss/Where are you!
Rich D.
2002-01-11 16:38:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks Mariss/Where are you!
mariss92705
2002-01-11 16:44:31 UTC
Re: Thanks Mariss/Where are you!
Carlos Guillermo
2002-01-11 17:00:49 UTC
RE: [CAD_CAM_EDM_DRO] Re: Thanks Mariss/Where are you!
Sven Peter
2002-01-11 18:03:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks Mariss/Where are you!
ballendo
2002-01-11 19:45:30 UTC
Re: Thanks Mariss/Where are you!
stevenson_engineers
2002-01-12 18:05:06 UTC
Re: Thanks Mariss/Where are you!