Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
Posted by
James Stevens
on 2002-01-15 09:01:44 UTC
J. Mark,
According to the Mitutoyo spec (in the mail to you today), the smallest
connector is a 5 pin. There are also 6 and 10 pin connectors, but no 4 pin.
I hope the spec provides some insight - although it looks like your scale
doesn't follow the Mitutoyo standard.
James
According to the Mitutoyo spec (in the mail to you today), the smallest
connector is a 5 pin. There are also 6 and 10 pin connectors, but no 4 pin.
I hope the spec provides some insight - although it looks like your scale
doesn't follow the Mitutoyo standard.
James
----- Original Message ----- >
> James Stevens <stevens@...> wrote:
> J. Mark,
>
> Until I get the full spec out to ya, check out this link. This describes
> the Mitutoyo SPC format of the data. It even has a PIC circuit to
interface
> with it.
>
> It lists a connector to interface (a 10 pin) but it looks like it's
> different than what you have.
>
> http://63.140.207.28/glib/muse145.pdf
>
>
>
>
> Hi James
>
> I stumbled upon that app note, and it is different. The issue I have now
is just finding connectors and/or cables to plug into my SPC output.
>
>
>
> "May a suitable landing spot be always on your glide slope"
> J. Mark Wolf, Pinckney, Michigan
> Rotorway Exec162F N1955Z
> Check out my web site at: www.rotorwaybuilders.net/ucosm
Discussion Thread
jmarkwolf
2002-01-07 18:13:17 UTC
Fresh run at homebrew DRO
ccs@m...
2002-01-07 18:20:03 UTC
Re: [CAD_CAM_EDM_DRO] Fresh run at homebrew DRO
James Stevens
2002-01-08 08:32:44 UTC
Re: [CAD_CAM_EDM_DRO] Fresh run at homebrew DRO
Scot Rogers
2002-01-08 09:17:42 UTC
test
J. Mark Wolf
2002-01-08 10:42:02 UTC
Re: [CAD_CAM_EDM_DRO] Fresh run at homebrew DRO
ppump11578@a...
2002-01-08 12:31:40 UTC
Re: [CAD_CAM_EDM_DRO] Fresh run at homebrew DRO
J. Mark Wolf
2002-01-12 18:59:11 UTC
Re: Fresh run at homebrew DRO
Doug Fortune
2002-01-12 19:32:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
Dr.D
2002-01-12 20:12:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
J. Mark Wolf
2002-01-13 06:29:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
James Stevens
2002-01-14 08:45:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
J. Mark Wolf
2002-01-14 16:24:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
James Stevens
2002-01-15 09:01:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
J. Mark Wolf
2002-01-23 09:54:32 UTC
Re:Fresh run at homebrew DRO