Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
Posted by
J. Mark Wolf
on 2002-01-14 16:24:44 UTC
James Stevens <stevens@...> wrote:
J. Mark,
Until I get the full spec out to ya, check out this link. This describes
the Mitutoyo SPC format of the data. It even has a PIC circuit to interface
with it.
It lists a connector to interface (a 10 pin) but it looks like it's
different than what you have.
http://63.140.207.28/glib/muse145.pdf
Hi James
I stumbled upon that app note, and it is different. The issue I have now is just finding connectors and/or cables to plug into my SPC output.
"May a suitable landing spot be always on your glide slope"
J. Mark Wolf, Pinckney, Michigan
Rotorway Exec162F N1955Z
Check out my web site at: www.rotorwaybuilders.net/ucosm
---------------------------------
Do You Yahoo!?
Send FREE video emails in Yahoo! Mail.
[Non-text portions of this message have been removed]
J. Mark,
Until I get the full spec out to ya, check out this link. This describes
the Mitutoyo SPC format of the data. It even has a PIC circuit to interface
with it.
It lists a connector to interface (a 10 pin) but it looks like it's
different than what you have.
http://63.140.207.28/glib/muse145.pdf
Hi James
I stumbled upon that app note, and it is different. The issue I have now is just finding connectors and/or cables to plug into my SPC output.
"May a suitable landing spot be always on your glide slope"
J. Mark Wolf, Pinckney, Michigan
Rotorway Exec162F N1955Z
Check out my web site at: www.rotorwaybuilders.net/ucosm
---------------------------------
Do You Yahoo!?
Send FREE video emails in Yahoo! Mail.
[Non-text portions of this message have been removed]
Discussion Thread
jmarkwolf
2002-01-07 18:13:17 UTC
Fresh run at homebrew DRO
ccs@m...
2002-01-07 18:20:03 UTC
Re: [CAD_CAM_EDM_DRO] Fresh run at homebrew DRO
James Stevens
2002-01-08 08:32:44 UTC
Re: [CAD_CAM_EDM_DRO] Fresh run at homebrew DRO
Scot Rogers
2002-01-08 09:17:42 UTC
test
J. Mark Wolf
2002-01-08 10:42:02 UTC
Re: [CAD_CAM_EDM_DRO] Fresh run at homebrew DRO
ppump11578@a...
2002-01-08 12:31:40 UTC
Re: [CAD_CAM_EDM_DRO] Fresh run at homebrew DRO
J. Mark Wolf
2002-01-12 18:59:11 UTC
Re: Fresh run at homebrew DRO
Doug Fortune
2002-01-12 19:32:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
Dr.D
2002-01-12 20:12:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
J. Mark Wolf
2002-01-13 06:29:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
James Stevens
2002-01-14 08:45:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
J. Mark Wolf
2002-01-14 16:24:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
James Stevens
2002-01-15 09:01:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Fresh run at homebrew DRO
J. Mark Wolf
2002-01-23 09:54:32 UTC
Re:Fresh run at homebrew DRO