uh, Mariss, can you clear up my confusion ?
Posted by
dave_ace_me
on 2002-02-14 17:23:38 UTC
from post: 39596 Subject: Re: Gecko G201
<sinp> (1) A full step drive needs 200 pulses to
second on a standard stepper, alas,
I knew that was too much to hope for.
then <snip> > Maximum speed at 250 oz-in is
(actually 300 steps per second)
Since I want to drive a 120 inch long lead screw,
am I screwed ? that is roughly 12 minutes for a
10 ft travel. or if use a 0.9 deg per step,
that would double to just over 23 minutes.
now that is truly agonizing !
what is a good solution ?
How fast can you spin a servo ?
Dave
(wishing the laws of physics didn't apply
to those of us in New Jersey)
<sinp> (1) A full step drive needs 200 pulses to
> turn 1 rev. A 10 uStep drive needs 2000.I was hoping I could get 4,000 steps per
> A full step drive needs 4,000 step pulses per
> second to turn a motor at 1,200 RPM, while
> the 10 uStep drive needs 40,000 for the
> same speed. Many cannot come up with the
> higher step pulse frequency. <big snip>
second on a standard stepper, alas,
I knew that was too much to hope for.
then <snip> > Maximum speed at 250 oz-in is
> 360 full steps per second. On a 10 TPIthis is more in what I had experienced,
> leadscrew this is an agonizingly slow 10.8 IPM.
>
(actually 300 steps per second)
Since I want to drive a 120 inch long lead screw,
am I screwed ? that is roughly 12 minutes for a
10 ft travel. or if use a 0.9 deg per step,
that would double to just over 23 minutes.
now that is truly agonizing !
what is a good solution ?
How fast can you spin a servo ?
Dave
(wishing the laws of physics didn't apply
to those of us in New Jersey)
> Marissdriven
>
> --- In CAD_CAM_EDM_DRO@y..., "rsgoldner" <rgoldner@i...> wrote:
> > Mariss, is this right? Given my three motors at 3V/4A phase
> > by G201s do I need about 60V at 10A or 60V at 2A? Big differencein
> > cost!
> >
Discussion Thread
NCS
2002-02-14 14:17:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: ...power...
rsgoldner
2002-02-14 14:32:29 UTC
Re: ...power... (Need Mariss)
mariss92705
2002-02-14 14:56:05 UTC
Re: ...power...
mariss92705
2002-02-14 15:17:13 UTC
Re: ...power... (Need Mariss)
rsgoldner
2002-02-14 15:27:35 UTC
Re: ...power... (Need Mariss)
studleylee
2002-02-14 15:46:26 UTC
Re: ...power... Gecko ready stuff...FYI
dave_ace_me
2002-02-14 17:23:38 UTC
uh, Mariss, can you clear up my confusion ?
mariss92705
2002-02-14 17:57:53 UTC
Re: uh, Mariss, can you clear up my confusion ?
ccs@m...
2002-02-14 19:15:43 UTC
Re: [CAD_CAM_EDM_DRO] uh, Mariss, can you clear up my confusion ?
dave_ace_me
2002-02-14 20:09:27 UTC
Re: uh, Mariss, can you clear up my confusion ?
mariss92705
2002-02-14 22:17:24 UTC
Re: uh, Mariss, can you clear up my confusion ?
Jon Elson
2002-02-14 23:12:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: ...power...
dave_ace_me
2002-02-15 05:06:57 UTC
Re: uh, Mariss, can you clear up my confusion ?
NCS
2002-02-21 14:47:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: ...power...