CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] plc compatibility was Re: Emco Tool Turret

Posted by Chris L
on 2002-02-24 08:03:34 UTC
Flashcut: Yes
cl

ballendo wrote:

> Hello,
>
> ah-Ha! definitely, and FLashcut, maybe... I don't think CncPRO does
> this.
>
> Ballendo
>
> --- In CAD_CAM_EDM_DRO@y..., Alan Marconett KM6VV <KM6VV@a...> wrote:
> > Hi Mark,
> >
> > I'm not sure, but I seem to remember a controller with a "PLC"
> > interface, which would allow one to start an external process, and
> wait
> > for it's completion. It might have been CNCpro?
> >
> > Alan KM6VV
> >
> > Mark Fraser wrote:
> > >
> > > I'd want to be able to use this in conjunction with CNCPro, for
> > > example, so that means an M-code which would drive some hardware
> > > and which would imply a "wait" for an appropriate time. Given
> > > that there's not likely an "I'm ready to go again" signal
> detection
> > > capability in cncpro, I'm hoping there's an M-code that would do.
> > >
> > > There would have to be some manually confirmed initialization
> > > for new running programs, and attention to details on loops and
> > > subroutines.
> > >
> > > I don't see the point in stepperizing it, just use a signal from
> > > the parallel port to drive the turret through "n" increments
> > > (i.e., "n" tool positions) as they appear in your program, and at
> > > the end of each cycle, the hardware backs the turret up to hold
> > > it in position. If there isn't an M code that implies a time
> > > delay, send a g1 line to an axis that isn't currently ON, with
> > > the feedrate suitable for the delay desired. Assuming we start
> > > at a "0" position, and it takes the turret 1 second to move to
> the
> > > next position, and the chosen axis has a feed rate of 1
> inch/second,
> > > send it a G01 A0.5
> > > G01 A0
> > >
> > > for each increment. It's up to the coder to keep track. At
> least that
> > > is what *I* plan to do with mine.... /mark
> > >
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

Mark Fraser 2002-02-22 15:55:20 UTC Emco Tool Turret Alan Marconett KM6VV 2002-02-22 23:47:44 UTC Re: [CAD_CAM_EDM_DRO] Emco Tool Turret ballendo 2002-02-23 09:22:25 UTC plc compatibility was Re: Emco Tool Turret Chris L 2002-02-24 08:03:34 UTC Re: [CAD_CAM_EDM_DRO] plc compatibility was Re: Emco Tool Turret