RE: [CAD_CAM_EDM_DRO] help!
Posted by
Bob Campbell
on 2002-05-26 14:55:24 UTC
Mark,
Go to www.geckodrive.com and download their white paper. It should have most
of the information that you are asking for.
Bob
-----Original Message-----
From: mabw [mailto:mabw@...]
Sent: Sunday, May 26, 2002 2:40 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] help!
Hi every one,
Sorry about the basic questions but i am very raw at this. I have
bought three of the Gecko 201 closeout drives and I wish to ask a few
dumbo questions, here goes!,
The stepper motors I have are 3 volt , 4 amp 6 wire jobs and I want
to get the most torque out of them with no real concern about fast
feed rates so , do I wire them as 4 wire leaving the center taps
vacant, if so what is the resistor value required? or do i 4 wire
using two end taps and the two center taps , again what size
resistor? I know the guide that came with the drives does explain it
but as I am so hopeless with this stuff that i would rather ask the
experts than stuff the drives!
kindest regards
Mark
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this as a sister
site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Go to www.geckodrive.com and download their white paper. It should have most
of the information that you are asking for.
Bob
-----Original Message-----
From: mabw [mailto:mabw@...]
Sent: Sunday, May 26, 2002 2:40 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] help!
Hi every one,
Sorry about the basic questions but i am very raw at this. I have
bought three of the Gecko 201 closeout drives and I wish to ask a few
dumbo questions, here goes!,
The stepper motors I have are 3 volt , 4 amp 6 wire jobs and I want
to get the most torque out of them with no real concern about fast
feed rates so , do I wire them as 4 wire leaving the center taps
vacant, if so what is the resistor value required? or do i 4 wire
using two end taps and the two center taps , again what size
resistor? I know the guide that came with the drives does explain it
but as I am so hopeless with this stuff that i would rather ask the
experts than stuff the drives!
kindest regards
Mark
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this as a sister
site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
mabw
2002-05-26 14:40:17 UTC
help!
Bob Campbell
2002-05-26 14:55:24 UTC
RE: [CAD_CAM_EDM_DRO] help!
mariss92705
2002-05-26 15:06:51 UTC
Re: help!
JanRwl@A...
2002-05-26 15:41:48 UTC
Re: [CAD_CAM_EDM_DRO] help!