Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Posted by
Alan Marconett KM6VV
on 2002-08-30 14:53:47 UTC
Thanks Jon,
I'll check out STG. Although I like the flexibility of your 1284
interface more! Just found it,
http://www.servotogo.com/
For those that might look, Cheap! $888! Yeah, I wouldn't mind having
one for testing!
Alan KM6VV
Jon Elson wrote:
I'll check out STG. Although I like the flexibility of your 1284
interface more! Just found it,
http://www.servotogo.com/
For those that might look, Cheap! $888! Yeah, I wouldn't mind having
one for testing!
Alan KM6VV
Jon Elson wrote:
>
> Alan Marconett KM6VV wrote:
>
> > Jon,
> >
> > Actually, I was asking if you happened to know about the "servo to go"
> > board commands. But thanks for the info on your boards.
> >
>
> The servo to go board looks a lot like my board, except the connection is
> direct to the ISA bus, so the IEEE-1284 protocol is not needed.
>
> The basic info on the board is on their web site for download, as far as
> I remember. You also need to get the info on the encoder chips from
> US Digital. The STG board just brings the functions of the encoder
> chip out to the ISA bus. The DAC and DIO are pretty simple, and
> the STG manual should be sufficient documentation.
>
> Jon
Discussion Thread
Alan Marconett KM6VV
2002-08-28 10:17:10 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Jon Elson
2002-08-28 17:54:17 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Jon Elson
2002-08-28 18:02:26 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Alan Marconett KM6VV
2002-08-28 18:19:52 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Carol & Jerry Jankura
2002-08-28 19:40:16 UTC
RE: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Jon Elson
2002-08-29 00:31:08 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Jon Elson
2002-08-29 00:40:15 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Alan Marconett KM6VV
2002-08-29 10:16:21 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Jon Elson
2002-08-29 20:15:22 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Alan Marconett KM6VV
2002-08-29 20:28:19 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Jon Elson
2002-08-30 10:50:11 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX
Alan Marconett KM6VV
2002-08-30 14:53:47 UTC
Re: [CAD_CAM_EDM_DRO] Servo to go card's, RUTEX