RE: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY
Posted by
JJ
on 2002-09-17 11:09:42 UTC
The output of the dominant supply (the one with the higher output
voltage) will carry the load until it's output voltage reaches the other
supply's voltage. The second supply starts to take up the slack at that
point. If the dominant supply shut down due to current limit, the second
would also, since it would be carrying the full load.
Regards,
JJ
Be Kind, Be Careful, Be Yourself
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
voltage) will carry the load until it's output voltage reaches the other
supply's voltage. The second supply starts to take up the slack at that
point. If the dominant supply shut down due to current limit, the second
would also, since it would be carrying the full load.
Regards,
JJ
Be Kind, Be Careful, Be Yourself
> -----Original Message-----http://groups.yahoo.com/group/jobshophomeshop I consider this as a
> From: elson [mailto:elson] On Behalf Of Jon Elson
> Sent: Tuesday, September 17, 2002 11:12 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY
>
>
> ers2001ckk wrote:
>
> > I have many surplus switching power supply adaptor
> > output at 24VDC 2amp. I connect 2 pcs in parallel
> > with diod in5 at the positive end supply to the GECKO 320
> > running a DC motor at 3.5 amp using Turbocnc and run it
> > for many hours. The end results is 1 is hotter than the other
> > the output measured 2 amp. Funny 2+2= 4, howcome 2+2=2
> > Any power supply experts out there can advice me.
>
> The two power supplies have slightly different voltage settings. One
> supply will always carry all the load, up to the maximum rating of
> that supply, at which point it will current limit, anf the
> other supply will
> start to carry the load. In your case, I suppose one supply
> is providing
> 2.5 A or so, whatever the current limit is actually set to,
> and the other
> is maybe providing 1 A.
>
> Jon
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com
> to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
Discussion Thread
ers2001ckk
2002-09-17 09:22:01 UTC
24VDC POWER SUPPLY
caudlet
2002-09-17 10:19:55 UTC
Re: 24VDC POWER SUPPLY
JJ
2002-09-17 10:26:15 UTC
RE: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY
Jon Elson
2002-09-17 11:00:06 UTC
Re: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY
JJ
2002-09-17 11:09:42 UTC
RE: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY