RE: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY
Posted by
JJ
on 2002-09-17 10:26:15 UTC
Use a low resistance, high wattage resistor on each supply. Connect the
other ends together, then connect to the Gecko.
Ps 1 ---/\/\/\/----+
+---- to Gecko
Ps 2 ---/\/\/\/----+
If you can find a 0.5 ohm, that would work. Radio shack has 0.47 ohms
that will work. You'll need 2 watt or larger if you go with the 0.47 ohm
ones. At full load this will lower the output voltage to 22.12 volts.
Your diode setup is probably lower than that, so it shouldn't be a
problem.
Regards,
JJ
Be Kind, Be Careful, Be Yourself
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
other ends together, then connect to the Gecko.
Ps 1 ---/\/\/\/----+
+---- to Gecko
Ps 2 ---/\/\/\/----+
If you can find a 0.5 ohm, that would work. Radio shack has 0.47 ohms
that will work. You'll need 2 watt or larger if you go with the 0.47 ohm
ones. At full load this will lower the output voltage to 22.12 volts.
Your diode setup is probably lower than that, so it shouldn't be a
problem.
Regards,
JJ
Be Kind, Be Careful, Be Yourself
> -----Original Message-----http://groups.yahoo.com/group/jobshophomeshop I consider this as a
> From: ers2001ckk [mailto:chan@...]
> Sent: Tuesday, September 17, 2002 9:22 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY
>
>
> I have many surplus switching power supply adaptor
> output at 24VDC 2amp. I connect 2 pcs in parallel
> with diod in5 at the positive end supply to the GECKO 320
> running a DC motor at 3.5 amp using Turbocnc and run it
> for many hours. The end results is 1 is hotter than the other
> the output measured 2 amp. Funny 2+2= 4, howcome 2+2=2
> Any power supply experts out there can advice me.
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com
> to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
Discussion Thread
ers2001ckk
2002-09-17 09:22:01 UTC
24VDC POWER SUPPLY
caudlet
2002-09-17 10:19:55 UTC
Re: 24VDC POWER SUPPLY
JJ
2002-09-17 10:26:15 UTC
RE: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY
Jon Elson
2002-09-17 11:00:06 UTC
Re: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY
JJ
2002-09-17 11:09:42 UTC
RE: [CAD_CAM_EDM_DRO] 24VDC POWER SUPPLY