RE: [CAD_CAM_EDM_DRO] Capacitors, no CAD, EDM, DRO content but maybe CNC
Posted by
Lloyd Leung
on 2002-10-18 16:14:05 UTC
When building my own power supply, I combined two small CAPS to make a
larger one.
You could buy a LARGE one, but I never found a reason why I should spend
$70CDN on a LARGE cap, when I could spend $24CDN for two smaller one.
When the two smaller ones are combined the unit has the same uF that I
needed.
(Btw, I forget if that was in series or parallel, it's been a few
months)
Cheers.
-----Original Message-----
From: Randy Gordon-Gilmore [mailto:zephyrus@...]
Sent: October 18, 2002 6:30 PM
To: cad_cam_edm_dro@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Capacitors, no CAD, EDM, DRO content but
maybe CNC
I forgot to mention that MECI also has nice big electrolytic caps for
your
power supply at cheap prices.
Best regards,
Randy (watch your test indicator point while you're jogging your CNC
around to indicate the vise. Mine sprang off when I jogged in the wrong
direction and landed somewhere over near the corner of the garage and I
have not found it yet. Thank goodness those things have overload
protection...)
Randy Gordon-Gilmore ,----.___________ ______________
_________________
ProtoTrains // = = === == || == == == = || == == == = ==
=|
Rio Vista, CA, USA
/-O==O------------o==o------------o==o-----------o==o-'
zephyrus@...
http://www.prototrains.com
larger one.
You could buy a LARGE one, but I never found a reason why I should spend
$70CDN on a LARGE cap, when I could spend $24CDN for two smaller one.
When the two smaller ones are combined the unit has the same uF that I
needed.
(Btw, I forget if that was in series or parallel, it's been a few
months)
Cheers.
-----Original Message-----
From: Randy Gordon-Gilmore [mailto:zephyrus@...]
Sent: October 18, 2002 6:30 PM
To: cad_cam_edm_dro@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Capacitors, no CAD, EDM, DRO content but
maybe CNC
I forgot to mention that MECI also has nice big electrolytic caps for
your
power supply at cheap prices.
Best regards,
Randy (watch your test indicator point while you're jogging your CNC
around to indicate the vise. Mine sprang off when I jogged in the wrong
direction and landed somewhere over near the corner of the garage and I
have not found it yet. Thank goodness those things have overload
protection...)
Randy Gordon-Gilmore ,----.___________ ______________
_________________
ProtoTrains // = = === == || == == == = || == == == = ==
=|
Rio Vista, CA, USA
/-O==O------------o==o------------o==o-----------o==o-'
zephyrus@...
http://www.prototrains.com
Discussion Thread
Randy Gordon-Gilmore
2002-10-18 15:30:50 UTC
Capacitors, no CAD, EDM, DRO content but maybe CNC
Lloyd Leung
2002-10-18 16:14:05 UTC
RE: [CAD_CAM_EDM_DRO] Capacitors, no CAD, EDM, DRO content but maybe CNC
Raymond Heckert
2002-10-18 20:00:44 UTC
Re: [CAD_CAM_EDM_DRO] Capacitors, no CAD, EDM, DRO content but maybe CNC
wanliker@a...
2002-10-18 20:16:41 UTC
Re: [CAD_CAM_EDM_DRO] Capacitors, no CAD, EDM, DRO content but maybe CNC
Lloyd Leung
2002-10-18 20:58:31 UTC
RE: [CAD_CAM_EDM_DRO] Capacitors, no CAD, EDM, DRO content but maybe CNC
jagco1998
2002-10-18 21:45:49 UTC
Re: Capacitors, no CAD, EDM, DRO content but maybe CNC
JJ
2002-10-19 09:54:20 UTC
RE: [CAD_CAM_EDM_DRO] Capacitors, no CAD, EDM, DRO content but maybe CNC
Scot Rogers
2002-10-19 11:12:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Capacitors, no CAD, EDM, DRO content but maybe CNC
w.higdon@a...
2002-10-19 11:17:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Capacitors, no CAD, EDM, DRO content but maybe CNC
Scot Rogers
2002-10-19 11:27:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Capacitors, no CAD, EDM, DRO content but maybe CNC
Scot Rogers
2002-10-19 11:37:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Capacitors, no CAD, EDM, DRO content but maybe CNC
wanliker@a...
2002-10-19 12:52:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Capacitors, no CAD, EDM, DRO content but maybe CNC
JanRwl@A...
2002-10-19 14:26:29 UTC
Re: [CAD_CAM_EDM_DRO] Capacitors, no CAD, EDM, DRO content but maybe CNC
JanRwl@A...
2002-10-19 14:43:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Capacitors, no CAD, EDM, DRO content but maybe CNC
MIKEC@W...
2002-10-19 15:12:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Capacitors, no CAD, EDM, DRO content but maybe CNC
Carol & Jerry Jankura
2002-10-19 17:59:00 UTC
RE: [CAD_CAM_EDM_DRO] Re: Capacitors, no CAD, EDM,DRO content but maybe CNC