RE: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"
Posted by
Dan Mauch
on 2002-10-30 08:35:26 UTC
http://206.19.206.56/dan_mauch_encoder_mount.htm is the url for the
linear encoders. I don't think it showed how I mounted the mylar strip
in the 1X2 rectangular tubing. Bascially, I used double sided 3 mil tape
cut down to 1/4" wide which was used to stick the mylar strip to a piece
of 1/4" aluminum square stock that was installed into the housing. The
slider machine to allow for the square stock.
Dan
-----Original Message-----
From: Roger Linscheid [mailto:r.linscheid@...]
Sent: Tuesday, October 29, 2002 7:48 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"
Thanks for the info, I think I'm going to give it a try. I feel that
the resolution should be adaquate for the majority of the work that I
do.
Dan, how did you mount the strip? I was thinking about a fiberglass
plane to support the strip. Hopefully this would lessen the effects
of temperature on the system, but perhaps this isn't needed.
I remember a website with pics of a linear encoder installation but I
guess I didn't bookmark it. Does anyone have a URL showing this
setup?
linear encoders. I don't think it showed how I mounted the mylar strip
in the 1X2 rectangular tubing. Bascially, I used double sided 3 mil tape
cut down to 1/4" wide which was used to stick the mylar strip to a piece
of 1/4" aluminum square stock that was installed into the housing. The
slider machine to allow for the square stock.
Dan
-----Original Message-----
From: Roger Linscheid [mailto:r.linscheid@...]
Sent: Tuesday, October 29, 2002 7:48 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"
Thanks for the info, I think I'm going to give it a try. I feel that
the resolution should be adaquate for the majority of the work that I
do.
Dan, how did you mount the strip? I was thinking about a fiberglass
plane to support the strip. Hopefully this would lessen the effects
of temperature on the system, but perhaps this isn't needed.
I remember a website with pics of a linear encoder installation but I
guess I didn't bookmark it. Does anyone have a URL showing this
setup?
Discussion Thread
Ken Jenkins
2002-10-29 11:59:21 UTC
Re: DRO issue "HEDs in hand"
Dan Mauch
2002-10-29 12:23:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"
Roger Linscheid
2002-10-29 19:47:40 UTC
Re: DRO issue "HEDs in hand"
John A. McFadden
2002-10-30 04:20:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"
j_e_f_f_williams
2002-10-30 05:57:40 UTC
Re: DRO issue "HEDs in hand"
Dan Mauch
2002-10-30 08:35:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"
John A. McFadden
2002-10-30 09:52:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"
John A. McFadden
2002-10-30 10:32:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"
j_e_f_f_williams
2002-10-30 11:40:03 UTC
Re: DRO issue "HEDs in hand"
j_e_f_f_williams
2002-10-30 11:44:26 UTC
Re: DRO issue "HEDs in hand"
John A. McFadden
2002-10-30 12:15:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"
j_e_f_f_williams
2002-10-30 18:21:25 UTC
Re: DRO issue "HEDs in hand"
John A. McFadden
2002-10-30 19:26:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: DRO issue "HEDs in hand"