RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Posted by
Bryan Mumford
on 2002-11-03 16:35:53 UTC
My motors are rated for 3.2 volts at 2 amps, driven with 24 volt choppers.
Higher voltages are a problem for small, low-cost tools. The Xylotex
drivers (3977 chip) max out at 35 volts, and the SLA7044 chip I'm
using is similar.
I'd be very interested in hearing from others who use 23 frame motors
on small tools. What step rates are you achieving?
Is anyone getting substantially more than 3300 steps per second, and
if so, what kind of driver are you using?
--
Bryan Mumford
Santa Barbara, California
http://www.bmumford.com
Higher voltages are a problem for small, low-cost tools. The Xylotex
drivers (3977 chip) max out at 35 volts, and the SLA7044 chip I'm
using is similar.
I'd be very interested in hearing from others who use 23 frame motors
on small tools. What step rates are you achieving?
Is anyone getting substantially more than 3300 steps per second, and
if so, what kind of driver are you using?
--
Bryan Mumford
Santa Barbara, California
http://www.bmumford.com
Discussion Thread
Marv Frankel
2002-11-03 07:54:39 UTC
Stepper motor speeds
turbulatordude
2002-11-03 08:26:35 UTC
Re: Stepper motor speeds
Tim Goldstein
2002-11-03 08:41:48 UTC
RE: [CAD_CAM_EDM_DRO] Stepper motor speeds
Marv Frankel
2002-11-03 14:03:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Tim Goldstein
2002-11-03 14:14:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Bryan Mumford
2002-11-03 15:43:50 UTC
[CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Tim Goldstein
2002-11-03 16:14:24 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Bryan Mumford
2002-11-03 16:35:53 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Bryan Mumford
2002-11-03 17:06:36 UTC
[CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Carol & Jerry Jankura
2002-11-03 17:12:32 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Bryan Mumford
2002-11-03 17:37:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Tim Goldstein
2002-11-03 18:12:47 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Tim Goldstein
2002-11-03 18:12:48 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Marv Frankel
2002-11-03 18:17:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Tim Goldstein
2002-11-03 18:22:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Shelbyville Design & Signworks
2002-11-03 19:53:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
B Snowden
2002-11-03 19:53:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Carol & Jerry Jankura
2002-11-03 20:32:03 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Marv Frankel
2002-11-03 23:27:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Tony Jeffree
2002-11-03 23:30:23 UTC
Re: Stepper motor speeds
Tim Goldstein
2002-11-03 23:42:54 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
Tony Jeffree
2002-11-04 01:19:52 UTC
Re: Stepper motor speeds
turbulatordude
2002-11-04 07:10:12 UTC
Stepper vs Servo ( was Re: Stepper motor speeds
turbulatordude
2002-11-04 07:59:06 UTC
Re: Stepper motor speeds
Tim Goldstein
2002-11-04 09:42:48 UTC
Re: [CAD_CAM_EDM_DRO] Stepper vs Servo ( was Re: Stepper motor speeds
JJ
2002-11-05 18:22:10 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
JanRwl@A...
2002-11-05 20:03:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
JJ
2002-11-06 03:55:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
ajv2803959
2002-11-06 08:20:14 UTC
Re: Stepper motor speeds
JanRwl@A...
2002-11-06 15:18:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
MIKEC@W...
2002-11-06 20:56:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
sconkworks
2002-11-07 20:20:01 UTC
Re: Stepper motor speeds
JJ
2002-11-08 04:11:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds
turbulatordude
2002-11-08 04:56:37 UTC
Re: Stepper motor speeds
JJ
2002-11-08 05:34:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: Stepper motor speeds