Re: [CAD_CAM_EDM_DRO] AXIS CALIBERATION AND THE SAME OLD DIRTY POSITION COUNTER STUCK PROBLEM!! !

Now today i did one more thing I installed the EMC
on the same P-III system with the same stg-2 board
and am having no counter stuck problem!!
We didnt do any changes to our hardware. the only
thing
that we may have done may be that this time the STG-II
was plugged in someother isa slot but even that i am
not sure. since when we had this problem in past
then i remeber had tried the stg-2 in more than onle
slots.
Also even after getting our board repaired by stg
(they had replaced the BIG square PLD)we
had run emc and were having the same counter stuck
problem.
It seems perhaps this cheater hardware has compromised
somehow on this problem.

warm regards
babar

--- Les Watts <leswatts@...> wrote:

> GREAT Babar!
>
> I am at a total loss as to why that would happen...
> but it is good
> to see that the problem is solved. Paul might have
> the best insight
> as to what is going on. You are right- we need to
> understand
> what happened here.
>
> Les
>
> Leslie Watts
> L M Watts Furniture
> Tiger, Georgia USA
>

http://www.alltel.net/~leswatts/wattsfurniturewp.html

> engineering page:
> http://www.alltel.net/~leswatts/shop.html
> Surplus cnc for sale:
> http://www.alltel.net/~leswatts/forsale.html
> ----- Original Message -----
> From: "Babar" <riet91@...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>;
> <jan@...>
> Sent: Wednesday, December 11, 2002 6:41 AM
> Subject: Re: [CAD_CAM_EDM_DRO] AXIS CALIBERATION AND
> THE SAME OLD DIRTY
> POSITION COUNTER STUCK PROBLEM!! !
>
>
> > Hi
> >
> > Bingo! and finally our position counter stuck
> problem
> > has solved!
> > guess how we solved it? (infact we didnt do it, it
> > just solved!!)
> >
> > We were too much fedup with the problem and the
> last
> > things we
> > were trying was to run EMC over slower systems. We
> had
> > installed it
> > over a pentium-1 200 mmx maachine. doing this
> resulted
> > in major improvement as i told in my last post. we
> > were able to move each axis upto 5 volts. Then we
> had
> > to return this P1(it was borrowed)
> > so i just pulled out my hard drive out of it and
> put
> > it into
> > our pentium - III machine without reinstalling the
> EMC
> > with linux
> > now what we saw was a tremendous complete
> improvement
> > in our problem
> > and now the problem doesnt exist anymore. now we
> can
> > move each axis
> > upto full 10 vlotls without counters hanging.
> Althouh
> > this P-III
> > is the same P-III machine which was unable to run
> the
> > same STG-II card
> > with the same EMC version. and was making us mad
> and
> > crazy...
> >
> > The problem is solved somehow but it is still a
> > mystery that what
> > is the actual truoble? Paul, Les, Ray, Jon Elson
> and
> > Nasir
> > Please look into the matter. I think the future of
> > Servo based EMC
> > systems with STG-II depends on the solution of
> this
> > problem.
> > and I think the problem needs special attention.
> >
> > Just now we have tuned and caliberated our x and y
> > axis and now we can move x and y beds at 200 ips
> > without any vibration and noise!!
> > our z-axis encoder has some problem we hope to fix
> it
> > soon and i
> > hope we will be able to stand with happy users of
> EMC
> >
> >
> > regards
> > Babar
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES:
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe:
> CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe:
> CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@...
> Moderator: jmelson@...
> timg@... [Moderator]
> URL to this group:
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru
> Google.com to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I
> consider this to be a sister site to the CCED group,
> as many of the same members are there, for OT
> subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC
> DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT
> ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
>

__________________________________________________
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now.
http://mailplus.yahoo.com