Re: [CAD_CAM_EDM_DRO] Re: HELP: Bipolar stepper ciruit

Hi Jeff/ Tim, thank you for your responce, I'm greatful for your info. al

-------Original Message-------

From: CAD_CAM_EDM_DRO@yahoogroups.com
Date: 05 January 2003 19:19:09
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: HELP: Bipolar stepper ciruit

Hi Al,
Just to let you know, Tim mentioned my stepper driver (Xylotex
single axis). The MINIMUM required motor voltage is 8 Volts on this
drive, so a 6 Volt system will not work with it if that is your only
voltage source. If you can get 12V out there, then you could use my
board with your 'machine'. It also requires +5V for logic, but that
can be easily obtained with a 7805 to the 12V supply.

Jeff
http://www.xylotex.com
xylotex @ hotmail.com (take the spaces around the @ out)

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Tim Goldstein" <timg@k...>
wrote:

> Al,
>
> Pretty straight forward and many ways to do it. One solution that

comes

> to mind is to get a E-labs http://www.elabinc.com/ EDE-1204 bipolar
> stepper drive chip. It is a custom programmed PIC chip that

includes a

> step generator or can be driven by an external step generator. It
> outputs the proper phase signals to drive a L298 bridge. There are

also

> a number of step generator circuits in the files section of this

group

> that will directly drive a step and direction driver (

www.xylotex.com

> now has a low cost single axis stepper board ).
>
> Hope this helps. It is a little off topic for the group, but the

concept

> is identical to making a non-computer driven power feed which is

very on

> topic. So if we just talk about driving your machine without a

computer

> we can sneak this by Bill <g>. Actually there was a thread on this

about

> a week ago if you search the archives.
>
> Tim
> [Denver, CO]
> Sherline products at Deep Discount
> Mach1 & DeskCNC with credit card ordering
> www.KTMarketing.com/Sherline
>
>
>
> > -----Original Message-----
> >
> > Happy new year to all.
> > I'm looking for a cuircuit to run a small bipolar stepper.
> > I need a hand held controller as its for a telescope, all
> > the circuits I've seen are computer controlled and I have no way

of

> > draging my p.c/monitor out side :)
> > Hope someone can help. The makers controller runs of 6Volts
> > batteries. Thank you. al
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts
metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister
site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON
T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/


.

[Non-text portions of this message have been removed]