Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Posted by
Jon Elson
on 2003-02-01 22:38:47 UTC
Bob Simon wrote:
think I checked the terminals
and the readings looked OK.
effort, depending on the
way they are built.
Jon
>Well, I saved some money on the AC Tech drive. It seems that all threeArrgh! I'd better check mine, although it is an air-cooled spindle. I
>Precise spindles I acquired had at least one phase burned out in the
>windings. I checked the water jackets and all were hopelessly plugged with
>gradoo. These early spindles didn't have a thermostat in them to report an
>overheat fault back to the drive. Once the water flow stopped, it was toast
>city. At least the price was right, they were salvage from a dumpster. Now
>I know why they ended up there.
>
think I checked the terminals
and the readings looked OK.
>I opened up the spindle assemblies and saw there are a lot of appropriateIt might still be possible to rewind these spindles without massive
>components for a DIY bench top milling spindle. Nice bearing housings and
>labyrinth type seals. They use common Barden 103g angular contact bearing
>pairs. A little pricey, but easy to find.
>
>
effort, depending on the
way they are built.
Jon
Discussion Thread
Tom Murray <thomasm923@a...
2003-01-27 07:44:49 UTC
Sorry!
Bob Simon
2003-01-27 08:18:31 UTC
high frequency spindle motors
Jon Elson
2003-01-27 10:07:05 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Bob Simon
2003-01-27 16:59:34 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Jerry Kimberlin
2003-01-27 18:05:00 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Jon Elson
2003-01-27 21:13:35 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Jon Elson
2003-01-27 21:20:27 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Bob Simon
2003-01-28 07:58:29 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Jon Elson
2003-01-28 10:38:28 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Bob Simon
2003-01-28 11:21:21 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
mayfieldtm <mayfiet@i...
2003-01-28 12:39:06 UTC
Re: high frequency spindle motors
jmkasunich <jmkasunich@y...
2003-01-28 14:18:02 UTC
Re: high frequency spindle motors
Jon Elson
2003-01-28 22:36:57 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Jon Elson
2003-01-28 22:43:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: high frequency spindle motors
jim davies
2003-01-29 11:51:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: high frequency spindle motors
Bob Simon
2003-02-01 07:37:33 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Jon Elson
2003-02-01 22:38:47 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
turbulatordude <davemucha@j...
2003-02-02 07:28:45 UTC
Re: high frequency spindle motors
Bob Simon
2003-02-04 16:02:55 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Jon Elson
2003-02-04 22:39:43 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Bob Simon
2003-02-05 08:35:20 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Raymond Heckert
2003-02-05 19:35:00 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Jon Elson
2003-02-05 22:30:56 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors
Nigel Bailey
2003-02-06 03:41:50 UTC
RE: [CAD_CAM_EDM_DRO] high frequency spindle motors
Jon Elson
2003-02-06 10:08:41 UTC
Re: [CAD_CAM_EDM_DRO] high frequency spindle motors