CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] high frequency spindle motors

Posted by Bob Simon
on 2003-02-04 16:02:55 UTC
>
>It might still be possible to rewind these spindles without massive
>effort, depending on the
>way they are built.

Now I'm wondering what I really have here. One of the units has a label
that says 40000rpm at 660hz,120 volts, 8.5 amps. I pulled it apart and
there was no visible (or olfactory) evidence of a burned winding. The
windings actually have 4 wires. There is a resistance of 2 ohms on each
pair of wires. there is no connection between the 2 pairs of wires. I think
I have a *2 phase* AC induction motor. I did a little reading on polyphase
motors and discovered that there were actually 2 phase motors used at one
time. Instead of a 120 degree phasing they require 90 degrees between the
phases.

I think I may be screwed as far as applying a 3 phase inverter to these
motors.

-Bob

Discussion Thread

Tom Murray <thomasm923@a... 2003-01-27 07:44:49 UTC Sorry! Bob Simon 2003-01-27 08:18:31 UTC high frequency spindle motors Jon Elson 2003-01-27 10:07:05 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Bob Simon 2003-01-27 16:59:34 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Jerry Kimberlin 2003-01-27 18:05:00 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Jon Elson 2003-01-27 21:13:35 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Jon Elson 2003-01-27 21:20:27 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Bob Simon 2003-01-28 07:58:29 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Jon Elson 2003-01-28 10:38:28 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Bob Simon 2003-01-28 11:21:21 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors mayfieldtm <mayfiet@i... 2003-01-28 12:39:06 UTC Re: high frequency spindle motors jmkasunich <jmkasunich@y... 2003-01-28 14:18:02 UTC Re: high frequency spindle motors Jon Elson 2003-01-28 22:36:57 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Jon Elson 2003-01-28 22:43:12 UTC Re: [CAD_CAM_EDM_DRO] Re: high frequency spindle motors jim davies 2003-01-29 11:51:22 UTC Re: [CAD_CAM_EDM_DRO] Re: high frequency spindle motors Bob Simon 2003-02-01 07:37:33 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Jon Elson 2003-02-01 22:38:47 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors turbulatordude <davemucha@j... 2003-02-02 07:28:45 UTC Re: high frequency spindle motors Bob Simon 2003-02-04 16:02:55 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Jon Elson 2003-02-04 22:39:43 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Bob Simon 2003-02-05 08:35:20 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Raymond Heckert 2003-02-05 19:35:00 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Jon Elson 2003-02-05 22:30:56 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors Nigel Bailey 2003-02-06 03:41:50 UTC RE: [CAD_CAM_EDM_DRO] high frequency spindle motors Jon Elson 2003-02-06 10:08:41 UTC Re: [CAD_CAM_EDM_DRO] high frequency spindle motors