Re: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Posted by
Jon Elson
on 2003-02-16 15:11:47 UTC
Jeff Goldberg wrote:
voltage is a very rough
guide, as much below that the speed suffers. Note that almost certainly
these motors were
running from a 130 V supply with the original controller.
capacitors. The
markings might be on the side, hidden by the clamp. But, you can
certainly go down
in voltage.
Jon
>Using the 125 volt primary and 44 volt secondary would give:This is your best bet. The 10% high is no big concern, the 25 x rated
>115/125 * 44 * 1.414 = 57 volts (10% too high based on 25 times rated volts)
>
>
voltage is a very rough
guide, as much below that the speed suffers. Note that almost certainly
these motors were
running from a 130 V supply with the original controller.
>3)You should not go UP in voltage without checking the rating on the
>Since I'm changing the voltage in the power supply from either 16.5 volts or
>130 volts (depending which supply I use to about 35 volts, can I continue to
>use the same capacitors? (and same size bridging resistors)?
>
>
capacitors. The
markings might be on the side, hidden by the clamp. But, you can
certainly go down
in voltage.
Jon
Discussion Thread
washcomp <jeff@w...
2003-02-12 06:25:30 UTC
QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS
Jon Elson
2003-02-12 10:09:46 UTC
Re: [CAD_CAM_EDM_DRO] QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS
Alper YILDIRIM
2003-02-13 02:44:07 UTC
Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS
turbulatordude <davemucha@j...
2003-02-13 05:33:19 UTC
Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Nigel Bailey
2003-02-13 06:54:06 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jeff Goldberg
2003-02-13 08:04:19 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Tony Jeffree
2003-02-13 08:53:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jon Elson
2003-02-13 09:28:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS
Mariss Freimanis <mariss92705@y...
2003-02-13 10:06:34 UTC
Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jeff Goldberg
2003-02-13 13:07:55 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Tony Jeffree
2003-02-13 14:19:55 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jeff Goldberg
2003-02-13 15:56:36 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
turbulatordude <davemucha@j...
2003-02-13 17:35:52 UTC
Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jeff Goldberg
2003-02-13 19:27:53 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
turbulatordude <davemucha@j...
2003-02-13 20:57:42 UTC
Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jon Elson
2003-02-13 21:30:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jon Elson
2003-02-13 21:43:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Tony Jeffree
2003-02-13 22:18:34 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Mariss Freimanis <mariss92705@y...
2003-02-13 22:25:44 UTC
Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
turbulatordude <davemucha@j...
2003-02-14 05:13:31 UTC
Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Nigel Bailey
2003-02-14 07:39:08 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jon Elson
2003-02-14 09:26:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jeff Goldberg
2003-02-14 14:07:55 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jeff Goldberg
2003-02-15 12:23:27 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Tim Goldstein
2003-02-15 12:32:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jeff Goldberg
2003-02-15 13:10:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jeff Goldberg
2003-02-15 14:26:10 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jeff Goldberg
2003-02-16 07:48:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Tim Goldstein
2003-02-16 08:40:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721
Jon Elson
2003-02-16 15:11:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: QUESTION ABOUT SERIES OR PARALLEL ON STEPPER MOTORS - ref post 52721