CAD CAM EDM DRO - Yahoo Group Archive

Re: plasma setup-leadscrew vs. rack & pinion + software

on 2003-02-19 22:57:34 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "caudlet <info@t...>"
<info@t...> wrote:
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Les Newell" <les@l...>
wrote:
> > Plasma cutting is not a very accurate process so don't waste your
> money on
> > ballscrews or acme leadscrews. They will be too low geared and
will
> fill up <snip>
>
>
> I just finished up a similar table. It is designed to be both a
> plasma and a router table so compromises had to be made. Router
> tables need accuracy and torque while plasma tables need speed.
>
> I used ballscrews because I got them cheap. The ballscrews (5TPI)
> limit the speed to about 180IPM because of "whipping". When you
spin
> long lengths of screw rod rapidly, it tends to start warping
(bowing)
> and can cause rapid wear in bearings and other components.
>
> If I was going to build just a plasma table I would probably pick
> rack and pinion. To figure what size gears you need, decided what
> the fastest speed is you want your rapid moves to be and work back
> using the step speed of the motors. It's always a tradeoff of
speed
> vs torque but on a plasma setup there is no drag created from the
> cutter (hopefully) so the torque needs are low. There are standard
> off-the-shelf rack and pinion sets so refine your design to fit
> what's available and cheap.
>
> For the Controller Software I have settled on MACH1 from the same
guy
> that wrote Master5 (mentioned by another list member). I chose it
> for several reasons but they primary one is that it is constantly
> being improved. One of the promised improvements is to incorporate
> the logic for doing a really low cost Torch Height Control (THC) by
> measuring the cut voltage and adjusting the Z height. Be advised
that
> MACH1 needs WIN2000 or XP to run. Check out the Master5 Group on
> yahoo.
>
> It won't help you now, but servo motors tend to have better RPM
specs
> and better torque at high speeds. Getting 1500 or even 3000 rpm
out
> of a servo motor is easy. Your gearing will have to be higher for
> steppers to get the same IPM moves. Take a look at
www.plasmacam.com
> for some ideas about rack and pinion setups.
>
> Drop me a line off list and I can go into detail about the THC
plans
> and some ideas for torch holders.
What e-mail address can we contact you at for info on the Z axis
control and torch holders? Thanks, Steve

Discussion Thread

nvlibby@c... 2003-02-19 07:15:50 UTC plasma setup-leadscrew vs. rack & pinion + software turbulatordude <davemucha@j... 2003-02-19 07:40:08 UTC Re: plasma setup-leadscrew vs. rack & pinion + software Les Newell 2003-02-19 08:52:13 UTC Re: [CAD_CAM_EDM_DRO] plasma setup-leadscrew vs. rack & pinion + software caudlet <info@t... 2003-02-19 11:18:20 UTC Re: plasma setup-leadscrew vs. rack & pinion + software CL 2003-02-19 14:43:58 UTC Re: [CAD_CAM_EDM_DRO] plasma setup-leadscrew vs. rack & pinion + software sierevello <sierevello@a... 2003-02-19 22:57:34 UTC Re: plasma setup-leadscrew vs. rack & pinion + software ballendo <ballendo@y... 2003-02-20 06:24:37 UTC Re: plasma setup-leadscrew vs. rack & pinion + software ironcrafters <nvlibby@c... 2003-02-21 16:07:27 UTC Re: plasma setup-leadscrew vs. rack & pinion + software turbulatordude <davemucha@j... 2003-02-21 17:01:31 UTC Re: plasma setup-leadscrew vs. rack & pinion + software