CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] plasma bridge

Posted by Les Newell
on 2003-03-08 00:56:11 UTC
HI Chris,
My plasma gantry is about 5' and rapids at 400 IPM with no problems. I have
had it running over twice that speed but it occasionally loses steps at high
speed. It is built like a T-square - the cross of the T uses spring loaded
skate bearings about 19" apart, running on a mild steel track. The other end
has a single skate bearing to take the weight. It is not exactly the
ultimate in precision machining but it is perfectly adequate for the work I
do.

My bridge is lighter than yours - I tried to keep the weight down as much as
possible. There are two reasons for the weight reduction exercise. Firstly
it gives better acceleration and secondly the machine is winched up into the
ceiling when not in use. I don't have enough spare space to have a 10" x 6"
machine sat on the floor all the time.

Les



> Has anyone built a plasma table driving a 5ft bridge or gantry from
> just one side? if so have you had any problems with it?
>
> Is there a formula to caculate how much force there will be on the
> side of the bridge that follows when it changes direction at max
> speed?
> I know my bridge ways about 40#s as it is curently designed, that I
> will be looking at speeds up to 400ipm in that axis and will be using
> dualvee type bearings.
>
> Thanks for all the help from everyone Im finally getting close!!
>
> Chris
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

ironarbor 2003-03-07 20:06:37 UTC plasma bridge caudlet 2003-03-07 20:25:44 UTC Re: plasma bridge Les Newell 2003-03-08 00:56:11 UTC Re: [CAD_CAM_EDM_DRO] plasma bridge turbulatordude 2003-03-08 06:08:36 UTC Re: plasma bridge James Owens 2003-03-08 06:26:54 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma bridge Erie Patsellis 2003-03-08 06:29:29 UTC RE: [CAD_CAM_EDM_DRO] plasma bridge Chris Ramirez 2003-03-08 07:56:03 UTC RE: [CAD_CAM_EDM_DRO] plasma bridge Doug Fortune 2003-03-08 09:17:22 UTC [CAD_CAM_EDM_DRO] Re: plasma bridge dakota8833 2003-03-08 12:28:42 UTC Re: plasma bridge James Owens 2003-03-08 15:18:13 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma bridge Les Newell 2003-03-08 17:26:04 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma bridge Les Newell 2003-03-08 17:26:06 UTC Re: [CAD_CAM_EDM_DRO] plasma bridge Les Newell 2003-03-08 17:26:09 UTC Re: [CAD_CAM_EDM_DRO] plasma bridge ccq@x... 2003-03-08 18:14:30 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma bridge Chris Ramirez 2003-03-08 18:25:54 UTC RE: [CAD_CAM_EDM_DRO] plasma bridge turbulatordude 2003-03-08 20:28:07 UTC Re: plasma bridge Shelbyville Design 2003-03-09 19:27:25 UTC Re: [CAD_CAM_EDM_DRO] plasma bridge Les Newell 2003-03-09 23:49:12 UTC Re: [CAD_CAM_EDM_DRO] plasma bridge